Fiberglass insulation is one of the most popular ways to keep your home warm. Since it's inexpensive, easy to find, and very dense, you can't go wrong with padding your walls. However, it's very squishy, so you might be a little confused about how to cut it. This is a very abrasive material that requires a sharp blade and some safety gear such as a dust mask and glasses. However, with some basic techniques, you can cut insulation board safely and efficiently.
Measuring insulating materials
Choose a piece of plywood that is at least as wide as the fiberglass board. Place it on a flat surface so there is enough room to spread out the fiberglass. The plywood doesn't have to be too big, just make sure it fits underneath the part you're cutting. [
Choose a sturdy piece of material, such as a piece of old plywood
You can put plywood on the floor for protection.
Avoid cutting bare surfaces such as concrete.
Wear cut-resistant gloves and other protective clothing. Fiberglass insulation is skin irritating, wear long pants and a long-sleeved shirt. Then, put on gloves, and some also wear disposable coveralls to prevent the insulation from spreading onto their clothing.
If part of your skin is exposed, apply some baby powder on it. The powder prevents glass shards in the insulation from sticking to the skin.
Wear a dust mask and safety glasses for protection. A regular N95 cloth dust mask will do just fine, if the mask you're using doesn't cover your eyes, buy separate glasses. Wear safety gear whenever cutting insulation.
The dust released by the insulation is harmful and can aggravate breathing problems such as asthma.
If you can, work outside so that dust doesn't settle in your home.
Unroll the insulating paper face down. Fiberglass insulation is rolled into a roll. Place the roll over the edge of the plywood. Then, push it through the plywood. Spread out just enough to make the cut you want to make.
Most insulation has a paper backing on one side. It's usually easier to cut the paper last, and the backing keeps the insulation clean when you unroll it.
Use a tape measure to determine where you will cut the insulation. Start by measuring where you plan to install the insulation. Plan to cut the insulation 1 inch (2.5 cm) larger than the insulation on all sides. Because fiberglass insulation is flexible, it can be tucked into tight places. The extra length will help it stay in place.
Mark the measurements on the insulator with a permanent marker. Use a tape measure to transfer the measurement to the insulator. Measure along both sides of the insulation, making small marks to indicate where you plan to cut.
If you roughly cut the insulation to approximate size, you don't need to take any additional measurements. If your goal is a precise cut, you can use a piece of sawdust to make a straight cut in most cases.
The need of every household and a must in every building construction, fiberglass tissue has been the talk of the town for ages. But what does it do? What is it used for? Let us help you put a full stop to your pondering! Fiberglass fleece is a fine matting that is similar to tissue paper. It is produced from glass fiber, be widely used in FRP composite surface applications and ensures smoothness and a clean look of colour to the surface. That isn't it; it also helps thermal resistance and ensures the durability of the product.
Having diversified uses, this fiberglass veil acts as an excellent fiberglass pipe wrapping tissue. It is used for pipe insulation to ensure the correct temperature of water flowing through. Secondly, it is also a fantastic choice for roofing tissue. It is used to produce bitumen membrane or bitumen shingles – whatever serves the purpose well. Moreover, it is also used as a fiberglass floor tissue that produces PVC floors. Apart from this, this is also an incredible choice for creating PVC carpets with long-lasting durability.
Coming over to its uses as a surface tissue, this is a go-to choice for many builders. Wondering why? As it is used for the surface treatment of Fiber Reinforced Plastic products. There's more to it – the fiberglass facing tissue can be used for internal wall decoration without worrying about leakage issues. Talking about wallboards and wallpaper choices, this fiberglass wallpaper and fiberglass facing tissue for wallboards are abundantly used to cover wallboard and internal wall decoration. Covering up acoustic boards is an issue in most households as well as buildings. This serves that purpose well too. Go for Fiberglass Acoustic Mat as it can be easily used as a surface layer of the acoustic board. The reason being that it is coated with CaC03 compound through a particular treatment.
Further, over to its battery use, this fiberglass battery separator tissue can be used as a lead-acid battery separator. Also, the commonly available black tissue is an excellent choice for thermal insulation. It can be for different materials; it serves as an insulation tape or insulation board, both. Lastly, fiberglass yellow tissue is also a good choice. It is widely being used as thermal insulation material to cover up the surface of the mineral wool board.
Glass Fiber Mat: Qualities
· Corrosion Resistant
· Excellent Strength
· It comes with an amazing strength to weight ratio
· Has high heat distortion temperature
· The incredible quality of being electrically non – conductive
· Ability to be moulded to precise tolerances
Fiberglass floor paper products are the base material for vinyl floors and decorative wallpapers. The floor and wallpaper made of this product have the characteristics of good stability, smooth appearance, bright color, and convenient laying. It is widely used as decoration materials in public entertainment places such as hospitals, schools, libraries, etc. It can also be used in high-grade floors and walls such as hotels, shopping malls, conference halls, office buildings, and residences.
Here is the content list:
Features of the fiberglass floor papers we sell
How can we provide you with products?
The fiberglass floor paper we sell is evenly dispersed, with a smooth surface, less wool, and easy-to-apply PVC. It is also stiff, resistant to folding, not easily deformed, and has good dimensional stability.
The PVC floor produced with fiberglass floor paper has the characteristics of good stability, smooth appearance, bright color, and convenient installation. PVC floor is a decorative material widely used in hospitals, schools, libraries, airports, and other public places.
Our products are packaged in standard export packaging for shipping.
1. Roll packing: PE plastic film.
2. Pallet Packing: Pallets should not be stacked in more than 2 layers.
3. The tray is free of fumigation, and a fumigation certificate can be provided.
Our fiberglass floor paper products should be stored in a dry, ventilated, rain-proof place with a temperature of 5°C to 35°C and a humidity of 35% to 65%. It is recommended to keep the intact packaging when not in use to avoid moisture.
If customers need specific unit weight, tensile strength, roll width, and roll length, NANJING EFG can produce according to customer requirements and provide tailor-made services to customers from different countries.
Our fiberglass floor paper products are loaded using standard export loading.
NANJING EFG has delivered materials to US, EU, Middle East, North Africa, South Africa, and Asia customers with guaranteed quality and good feedback. With rich export experience and technical support, NANJING EFG welcomes cooperation with customers from all over the world.
The materials are packed in the factory, then shipped to the seaport, and finally shipped to the customer's port by MSK, MSC, CMA, COSCO, YANGMING, APL, etc.
【Payment method】 LC, T/T, CAD, PAYPAL, WESTERN UNION, ETC.
Nanjing EFG CO., LTD tracks the goods of each shipment until the customer uses the material, and is ready to provide any assistance to the customer's needs.
If customers encounter any technical problems, Nanjing EFG CO., LTD will provide relevant knowledge to help customers find the best solution, and send technicians to customers' factories for guidance when necessary.
If you are interested in purchasing fiberglass, visit our website: https://www.china-fiberglass.com/to get more professional information about fiberglass. We will welcome you with high-quality products and good service as well as low prices! To provide comprehensive technical support to our customers, we will provide technical and other related information on time upon request.
Fiberglass has a great application in the field of decoration. Fiberglass floor towels and fiberglass carpet towels are examples, so when you cut a PVC floor or PVC carpet, you will find a thin layer of glass fiber in the middle of the PVC. The glass fiber makes the surface of the PVC floor flat and effectively avoids the deformation of the PVC floor and carpet. This is why PVC floors and carpets with a fiberglass core do not deform and blister in flooring applications.
Here is the content list:
Characteristics of fiberglass
Various applications of glass fibers
1. The fiberglass is uniformly dispersed and the surface is smooth
2. Excellent bonding performance with coatings
3. Waterproof and weather resistance, long service life
1.The glass fiber veneer paper directly covers the surface of the inner wall, making the wall smooth and textured. Fiberglass joint tapes are used as joint tapes for wall panel joints and wall crack/hole repair. Coated fiberglass mats are coated with a CaCO3 compound on the fiberglass mats. The coated fiberglass mat is used as a decoration mat to directly cover the uneven wall surface to avoid falling off of the decoration layer. Coated fiberglass mats are a quick and easy solution for updating walls.
2. Fiberglass filter media is also widely used in the field of air filtration. One of the applications is to use glass fiber filter paper as the skeleton layer, and the primary filter layer is laminated with glass fiber paper. The laminate is the functional part of the filter element. The second filter application is the use of glass fiber filter paper towels in environmental engineering to chemically remove VOC gases.
3. Fiberglass mat, polyester fiberglass mat, and CaCo3-coated fiberglass are ideal wallboard covering materials. Using these materials instead of kraft paper to cover the surface of the wallboard can effectively improve the breaking strength of the wallboard, and at the same time endow the wallboard with excellent characteristics such as waterproof, fireproof, heat insulation, and mildew resistance. Proven, scratch-resistant, etc.
4. Fiberglass battery separator paper towel is the first choice for all battery rooms, used as a separator for lead-acid batteries.
5. Glass fiber black paper towels, glass fiber yellow paper towels, and coated glass fiber mats are used as insulation materials for the surface of insulation boards such as mineral wool boards and polyurethane boards, giving insulation boards excellent breaking strength, and other functional properties, such as Fire and waterproof.
6. The fiberglass roof is used as the core material of the bituminous membrane. Also used as reinforcement for waterproof coatings. Asphalt can quickly impregnate fiberglass roof tissue, which retains and reinforces asphalt.
All in all, fiberglass has many uses and is recognized as the most important choice in all industries.
Our official website is https://www.china-fiberglass.com/. If you want to know more about fiberglass, you can communicate with us on the website. We will be glad to provide you with high-quality fiberglass, good service, and a competitive price to provide more and better service!
The glass fiber black felt adopts a thermosetting resin-based environmentally friendly formula adhesive to tightly bond the composite fibers, with good color fixation, high strength, wear resistance, and effective control of fiber scattering. Black fiberglass felt has excellent flame retardant, sound absorption and noise reduction, and thermal insulation effect. Anti-fouling and water-repellent, effectively avoid the growth and reproduction of various microorganisms, anti-bacterial and anti-mildew. Especially suitable for high-speed, high-speed rail sound-absorbing barriers, perforated sound-absorbing panels veneer, good light absorption, and zero reflection.
Here is the content list:
The role of Black fiberglass
Advantages and applications of Black fiberglass felt
Please rest assured to choose NANJING EFG
Black fiberglass is compounded on a glass wool board, which is a special material for heat preservation, sound absorption, and noise reduction. It acts on the lining of the glass wool air duct, absorbs the noise of the air duct system, reduces the loss of heat and cold on the air duct wall, and can meet the requirements of reducing energy consumption. requirements, greatly improving the indoor acoustic environment quality. It is especially suitable for environments with high mute requirements to improve sound quality and speech intelligibility. Such as high-end hotels, office buildings, clubs, and so on.
1.Antibacterial and mildew proof, the fiber is not easy to fall off.
2. Flame retardant.
3. Sound absorption, noise reduction, sound insulation, and thermal insulation performance.
4. Waterproof, oilproof, antifouling.
Used as high-speed rail, high-speed rail with sound-absorbing barriers, and perforated sound-absorbing panel veneer. Black fiberglass felt can also be used as air conditioner insulation panel veneer/glass wool panel veneer/ceiling back panel/solar flat panel heat collector panel veneer.
As an expert in glass fiber and non-woven materials, NANJING EFG started in 2006 and established the vision of "building an internationally renowned brand" in the field of glass fiber and non-woven materials.
Every employee of NANJING EFG incorporates this belief into their daily work and life. When you work with NANJING EFG, you will find that you are working with a professional team whose service is positive and efficient, with consistent quality and an unforgettable reputation.
NANJING EFG was established to meet various needs of wallboard, thermal insulation, reinforcement, insulation, filtration, surface treatment, decoration, paving, waterproofing, glass fiber reinforced plastic, electrical and electrical, etc., with fiberglass and non-glass fiber as the base material for woven materials. NANJING EFG has a well-trained and experienced technical team focused on providing "tailor-made" product and service solutions. NANJING EFG ensures the best product performance for your business at the lowest total cost. NANJING EFG's professional service team will provide you with high-quality products and efficient services on time.
If you are interested in purchasing fiberglass, visit our website: https://www.china-fiberglass.com/to get more professional information about fiberglass. We will welcome you with high-quality products and good service as well as low prices! To provide comprehensive technical support to our customers, we will provide technical and other related information promptly upon request.
Fiberglass is an inorganic non-metallic material with excellent performance. It is made of pyrophyllite, quartz sand, limestone, dolomite, boro site, and boro site as raw materials through high-temperature melting, wire drawing, winding, weaving, and other processes. The diameter of the monofilament is several microns to twenty microns, which is equivalent to 1/20-1/5 of a hair, and each bundle of fiber strands is composed of hundreds or even thousands of monofilaments. Fiberglass is usually used as reinforcing materials in composite materials, electrical insulating materials and thermal insulation materials, circuit substrates, and other fields of the national economy.
Here is the content list:
Main features of glass fiber
Melting point: glass is a kind of amorphous, with no fixed melting point, it is generally considered that its softening point is 500~750℃
Boiling point: about 1000 ℃
Density: 2.4~2.76 g/cm3
When fiberglass is used as a reinforcing material for reinforced plastics, the biggest feature is its high tensile strength. The tensile strength is 6.3 to 6.9 g/d in the standard state and 5.4 to 5.8 g/d in the wet state. Good heat resistance, no effect on strength when the temperature reaches 300 ℃. It has excellent electrical insulation, is an advanced electrical insulation material, and is also used for thermal insulation materials and fire shielding materials. Generally only corroded by concentrated alkali, hydrofluoric acid, and concentrated phosphoric acid.
Compared with organic fibers, fiberglass has higher temperature resistance, non-combustibility, corrosion resistance, good heat insulation, and sound insulation, high tensile strength, and good electrical insulation. These characteristics make the use of glass fiber far more extensive than other types of fibers, and the development speed is also far ahead.
(1) High tensile strength and small elongation.
(2) High elastic coefficient and good rigidity.
(3) The amount of elongation within the elastic limit is large and the tensile strength is high, so the absorption of the impact energy is large.
(4) Fiberglass is an inorganic fiber, which is non-flammable and has good chemical resistance.
(5) Low water absorption.
(6) The dimensional stability and heat resistance are all good.
(7) Good processability, can be made into different forms of products such as strands, bundles, felts, and woven fabrics.
(8) Transparent and permeable to light.
(9) Good adhesion to resin.
(10) The price is cheap.
(11) It is not easy to burn, and can be melted into glass beads at high temperatures.
NANJING EFG, https://www.china-fiberglass.com/, is a dynamic, creative, experienced, and responsible team. Everyone on the team is committed to providing the best products and services to our customers. Our company has developed a wide range of fiberglass which are tested extensively before leaving the factory to ensure quality. As a professional manufacturer, we specialize in manufacturing the highest quality fiberglass. We have conducted a large number of tests before leaving the factory to ensure the quality. You can consider using our cost-effective products. Thank you for your time!
Why is fleece used in fiberglassing.
1. It is a reinforcing material
In the process of GRG production, gypsum slurry and glass fiber are used alternately, layer by layer. The glass fiber helps to strengthen the firmness of the gypsum block and prevent the gypsum from being scattered after solidification.
2. It has high temperature resistance
It has been tested that when the temperature reaches 300°C, it has no effect on the strength of the glass fiber
3. It has high tensile strength
The tensile strength of glass fiber is 6.3~6.9 g/d in standard state and 5.4~5.8 g/d in wet state.
4.It has good electrical insulation
Glass fiber has excellent electrical insulation and is an advanced electrical insulation material. It is also used in heat insulation materials and fire shielding materials.
5. It is not easy to burn
Glass fiber can be melted into glass beads at high temperature, which meets the requirements of fire prevention and control in the construction industry.
6. It has good sound insulation
The combination of glass fiber and gypsum can achieve a good sound insulation effect.
7. It’s cheap
Regardless of the industry, cost control is the most important link, and products with high quality and low price will definitely be favored.
Well, the above are the seven advantages of why glass fiber can be widely used in the construction industry. Glass Fiber is a very good substitute for metal materials.
Tel: +86 25 52270147
Fax: +86 25 58321442 / 52255211
Mob: +86 18851651909
Whatsapp: 0086 18851651909