csm fiberglass- Factory Manufacturers Suppliers From China

Fiberglass insulation is one of the most popular ways to keep your home warm. Since it's inexpensive, easy to find, and very dense, you can't go wrong with padding your walls. However, it's very squishy, so you might be a little confused about how to cut it. This is a very abrasive material that requires a sharp blade and some safety gear such as a dust mask and glasses. However, with some basic techniques, you can cut insulation board safely and efficiently.

1. Measuring insulating materials

   Choose a piece of plywood that is at least as wide as the fiberglass board. Place it on a flat surface so there is enough room to spread out the fiberglass. The plywood doesn't have to be too big, just make sure it fits underneath the part you're cutting. [
   

   Choose a sturdy piece of material, such as a piece of old plywood

   You can put plywood on the floor for protection.

   Avoid cutting bare surfaces such as concrete.

2. Wear cut-resistant gloves and other protective clothing. Fiberglass insulation is skin irritating, wear long pants and a long-sleeved shirt. Then, put on gloves, and some also wear disposable coveralls to prevent the insulation from spreading onto their clothing.

   If part of your skin is exposed, apply some baby powder on it. The powder prevents glass shards in the insulation from sticking to the skin.

3. Wear a dust mask and safety glasses for protection. A regular N95 cloth dust mask will do just fine, if the mask you're using doesn't cover your eyes, buy separate glasses. Wear safety gear whenever cutting insulation.

   The dust released by the insulation is harmful and can aggravate breathing problems such as asthma.

   If you can, work outside so that dust doesn't settle in your home.

4. Unroll the insulating paper face down. Fiberglass insulation is rolled into a roll. Place the roll over the edge of the plywood. Then, push it through the plywood. Spread out just enough to make the cut you want to make.

   Most insulation has a paper backing on one side. It's usually easier to cut the paper last, and the backing keeps the insulation clean when you unroll it.

5. Use a tape measure to determine where you will cut the insulation. Start by measuring where you plan to install the insulation. Plan to cut the insulation 1 inch (2.5 cm) larger than the insulation on all sides. Because fiberglass insulation is flexible, it can be tucked into tight places. The extra length will help it stay in place.

6. Mark the measurements on the insulator with a permanent marker. Use a tape measure to transfer the measurement to the insulator. Measure along both sides of the insulation, making small marks to indicate where you plan to cut.

   If you roughly cut the insulation to approximate size, you don't need to take any additional measurements. If your goal is a precise cut, you can use a piece of sawdust to make a straight cut in most cases.

  Glass fiber is an organic substance, which itself is not harmful to the human body. But fine fiberglass dust is breathed into a person's lungs. Because glass cannot be absorbed and decomposed at all, it will form deposits for a long time, which will cause occupational diseases similar to silicosis. Although the damage is not fatal, it will affect people's respiratory function. Contact dermatitis often occurs in glass fiber workers, and a few people Skin sensitization occurs, but the fibers themselves have not been proven to be allergens so far.

If it's just pure skin contact, there are generally no other problems, the main reason is that it irritates the skin to a certain extent.

The opposite of Glass fiber is an inorganic non-metallic material with excellent performance. There are many kinds. The advantages are good insulation, strong heat resistance, good corrosion resistance and high mechanical strength, but the disadvantages are brittleness and poor wear resistance. It is made of glass balls or waste glass through high-temperature melting, wire drawing, winding, weaving and other processes. The glass fiber is often used as reinforcing material of composite material, electrical insulation and heat insulation materials, substrate and other national economy fields.

Our company has been engaged in the glass fiber industry for more than ten years, and has rich experience and high-quality products. Welcome to contact us by fiberglass@njefg.com

Fiberglass is a glass material similar to the glass we have in our windows or the glass we drink our favorite slush in. But the best part about glass fiber is that it's durable, it's less brittle, it's very strong, and it's lightweight.

Starting it off with the manufacturing of fiberglass fleece, glass is heated up till the point that it starts to melt and is molten. It is then further on forced through superfine holes. This, in turn, gives us glass filaments that are very thin, thin to the extent that they are measured in microns. Interesting enough! This point is the fundamental base for how the fiberglass veil caters to such a diversified set of uses. These filament threads are flexible and can be molded into various complex shapes for many different applications.

Let us have a glimpse into the applications of glass fiber mats in various sectors of society.

Understanding how Fibre de Verre is durable, exceptionally safe, and offers high thermal insulation, fiberglass filter tissue is a widely preferred material in all industries. The main plus point is that apart from being an excellent insulation material, it is very cost-efficient. Here is its use in different sectors:

- Surface treatment of FRP products. In our daily life, you are using Fiberglass Reinforced Plastic (FRP) products anywhere: Body of metro, car parts, Medical instruments, boats, furniture, structure parts of buildings and industrial projects, FRP pipes...... Do you know why the surface of these FRP products are perfectly even and smooth ?  Fiberglass surface tissue is used as the surface material of these FPR products are the key reason.

- PVC floor and Carpet: Fiberglass Tissue have a large scale of application in the field of decoration. Fiberglass floor tissue and fiberglass carpet tissue are used as the stabilize layer of the PVC floor and PVC carpet , So do not surprise that when you cut the PVC floor or PVC carpet, you will find that in the middle of the PVC these is a thin core layer which is fiberglass layer. The fiberglass layer absorb the PVC quickly and give the of PVC floor an even surface, efficiently avoid deforming of PVC floor and carpet. That’s why the PVC floor and carpet which used fiberglass as core layer will not be find deforming and bubble in the floor application.

-  Acoustic panel:  Fiberglass Board is produced with unparalleled formula and process, the fiberglass board can reach the thickness 8mm till 10mm, the one layer polyporous structure make the fiberglass board has unique combination of abuse resistance and sound absorption. At the same time, the fiberglass Board has the features of heat reservation, thermal insulation and fire-proofing. Adding the excellent features of stiffness, light weight, bendable and easy cutting, the fiberglass board is very easy and simple to be further processed and installed. All these features make the fiberglass board an ideal material to improve the acoustic environment, decrease the loss of heat and keep the building safe from fire.

- Internal wall decoration: Fiberglass facing tissue is used to cover on the surface of internal wall directly, which give the wall even surface and quality feeling. Fiberglass non-woven tape is used as joint tape for the wall boards joint connection and crack/hole  repair of the wall.  Coated fiberglass mat is coating the CaCO3 compound on the fiberglass mat.  The coated fiberglass mat is used as redecoration mat to cover on the surface of uneven wall directly, avoided removing the decoration layer. The coated fiberglass mat is a fast and easy solution to renew the wall.

- Filtration:  Fiberglass filter tissue is widely used in the field of air filtration. One of the  applications is to use the fiberglass filter tissue as frame layer and primary filter layer to attach with fiberglass paper. The laminated material is the functional part of the filter element.  The second filtration application is to use the fiberglass filter tissue in the environmental project to remove the VOC gas by chemical method.

- Wall boards. Fiberglass mat, polyester fiberglass mat and CaCo3 Coated fiberglass are idea covering material of wall boards. Use these material to replace the craft paper to cover on the surface of wall boards can efficiently increase the break strength of the wall boards, at same time it can give the wall boards excellent features such as water proof, fire proof, thermal insulation, mildew proof, scratch resistant and so on.

- Batteries: Fiberglass Battery Separator tissue is the go-to choice at all battery houses for being used as a separator of lead-acid batteries.

- Insulation: Fiberglass Black Tissue , Fiberglass Yellow Tissues and coated fiberglass mat are used as thermal insulation material to be use on the surface of insulation boards such as mineral wool boards and polyurethane boards, give the insulation board excellent break strength and other functional features such as fireproof and waterproof.

     -    Waterproof :  Fiberglass roofing tissue is used as core material of bitumen membrane. Also be used as reinforce material of waterproof painting. Bitumen can impregnate the fiberglass roofing tissue quickly, fiberglass roofing tissue hold and reinforce the bitumen.

All in all, fiberglass has many uses and is known to be the most substantial choice in all industries.

It's fine, lightweight, strong, and above all, it's less brittle – Fiberglass tissue is a need at every construction site. Catering to a diversified set of requirements, fiberglass fleece can be easily molded into any shape. Taking this into consideration, it is easily understandable how fiberglass comes to use every day.

Be it fiberglass reinforced panels or fiberglass fleece, they are durable and long-lasting in every aspect. Here's a glimpse of how and where it is used.

1. Fiberglass Pipe Wrapping Tissue  

Fiberglass Pipe Wrapping Tissue is abundantly used to cover on the surface of steel pipe, being impregnated with bitumen or resin for the anti corrosion of the steel pipes.  Not only this, but fiberglass veil is also an excellent choice for under sink piping.

2. Fiberglass Roofing Tissue

It's excellent, water-resistant, and serves the purpose well – Fiberglass for roofing material is mainly used as a substrate for waterproofing materials. These include waterproofing membrane, asphalt, shingle, and much more. Having excellent waterproofing properties, this is characterized by high tensile strength, remarkable qualities of being water and corrosion resistance, its dimensional stability,  and easy saturation with bitumen. It is also used as reinforcing material of waterproofing painting.

3. Fiberglass Floor Tissues

The primary substrate material of plastic floor and PVC carpet. This might not be the case behind all, but the floor and carpet made with fiberglass floor tissue are more stable, have a smoother appearance, and come in bright colors with convenient laying. The common characteristics include uniformly dispersed fiber, smooth surface, less wool yarn, easy-to-coat PVC, stiffness properties, and folding resistance. Also, excellent dimensional stability is a plus point.

4. Fiberglass Facing Tissue for Wallboards

A Glass Fiber mat for wallboard is produced using the mixture of glass fiber and polyester fiber by the commonly known wet layout process. This excellent composition is the primary reason behind flexibility and stability in everyday use, making the wallboard mats more comfortable and smooth to touch. The polyester fiberglass mat gives the gypsum board remarkable qualities of waterproof, break strength, anti UV, anti-wrinkle, and anti-septic. The common characteristics include strong tensile strength, moisture resistance, mold resistance, and excellent air permeability.

5. Fiberglass Acoustic Boards

Fiberglass acoustic boards are the widely used for sound-absorbing panels that are placed on the walls, ceiling, and other places to absorb the noise and control the sound in a specific area, gives a quiet living environment. Glass Fiber acoustic boards has also features of excellent stiffness, light weight and be bendable, make it be easy mounting. The features of fire proof and formaldehyde make it be a environment friendly material, be suitable for the decoration market.  

Fiberglass is not made of glass.

Glass fiber is made of pyrophyllite, quartz sand, limestone, dolomite, boronite, and boronite as raw materials through high-temperature melting, wire drawing, winding, weaving and other processes. Its main components are silica, alumina, calcium oxide, boron oxide, magnesium oxide, sodium oxide, etc. According to the alkali content in the glass, it can be divided into alkali-free glass fibers (0% to 2% sodium oxide, which belongs to aluminum Borosilicate glass), medium-alkali glass fiber (sodium oxide 8% to 12%, which belongs to boron-containing or boron-free soda-lime silicate glass) and high-alkali glass fiber (more than 13% sodium oxide, which belongs to soda-calcium silicate glass) silicate glass).

Fiberglass is an inorganic non-metallic material with excellent performance. There are many kinds. Its advantages are good insulation, strong heat resistance, good corrosion resistance and high mechanical strength. Difference. The diameter of its monofilament is several microns to more than 20 microns, which is equivalent to 1/20-1/5 of a hair, and each bundle of fiber precursors is composed of hundreds or even thousands of monofilaments. The glass fiber is often used as reinforcing material of composite material, electrical insulation and heat insulation materials, substrate and other national economy fields.

                                         Why is fleece used in fiberglassing.

1. It is a reinforcing material

In the process of GRG production, gypsum slurry and glass fiber are used alternately, layer by layer. The glass fiber helps to strengthen the firmness of the gypsum block and prevent the gypsum from being scattered after solidification.

2. It has high temperature resistance

It has been tested that when the temperature reaches 300°C, it has no effect on the strength of the glass fiber

3. It has high tensile strength

The tensile strength of glass fiber is 6.3~6.9 g/d in standard state and 5.4~5.8 g/d in wet state.

4.It has good electrical insulation

Glass fiber has excellent electrical insulation and is an advanced electrical insulation material. It is also used in heat insulation materials and fire shielding materials.

5. It is not easy to burn

Glass fiber can be melted into glass beads at high temperature, which meets the requirements of fire prevention and control in the construction industry.

6. It has good sound insulation

The combination of glass fiber and gypsum can achieve a good sound insulation effect.

7. It’s cheap

Regardless of the industry, cost control is the most important link, and products with high quality and low price will definitely be favored.

Well, the above are the seven advantages of why glass fiber can be widely used in the construction industry. Glass Fiber is a very good substitute for metal materials.

Fiberglass has a great application in the field of decoration. Fiberglass floor towels and fiberglass carpet towels are examples, so when you cut a PVC floor or PVC carpet, you will find a thin layer of glass fiber in the middle of the PVC. The glass fiber makes the surface of the PVC floor flat and effectively avoids the deformation of the PVC floor and carpet. This is why PVC floors and carpets with a fiberglass core do not deform and blister in flooring applications.

Here is the content list:

• Characteristics of fiberglass

• Various applications of glass fibers

Characteristics of fiberglass

1. The fiberglass is uniformly dispersed and the surface is smooth

2. Excellent bonding performance with coatings

3. Waterproof and weather resistance, long service life

Various applications of glass fibers

1.The glass fiber veneer paper directly covers the surface of the inner wall, making the wall smooth and textured. Fiberglass joint tapes are used as joint tapes for wall panel joints and wall crack/hole repair. Coated fiberglass mats are coated with a CaCO3 compound on the fiberglass mats. The coated fiberglass mat is used as a decoration mat to directly cover the uneven wall surface to avoid falling off of the decoration layer. Coated fiberglass mats are a quick and easy solution for updating walls.

2. Fiberglass filter media is also widely used in the field of air filtration. One of the applications is to use glass fiber filter paper as the skeleton layer, and the primary filter layer is laminated with glass fiber paper. The laminate is the functional part of the filter element. The second filter application is the use of glass fiber filter paper towels in environmental engineering to chemically remove VOC gases.

3. Fiberglass mat, polyester fiberglass mat, and CaCo3-coated fiberglass are ideal wallboard covering materials. Using these materials instead of kraft paper to cover the surface of the wallboard can effectively improve the breaking strength of the wallboard, and at the same time endow the wallboard with excellent characteristics such as waterproof, fireproof, heat insulation, and mildew resistance. Proven, scratch-resistant, etc.

4. Fiberglass battery separator paper towel is the first choice for all battery rooms, used as a separator for lead-acid batteries.

5. Glass fiber black paper towels, glass fiber yellow paper towels, and coated glass fiber mats are used as insulation materials for the surface of insulation boards such as mineral wool boards and polyurethane boards, giving insulation boards excellent breaking strength, and other functional properties, such as Fire and waterproof.

6. The fiberglass roof is used as the core material of the bituminous membrane. Also used as reinforcement for waterproof coatings. Asphalt can quickly impregnate fiberglass roof tissue, which retains and reinforces asphalt.

All in all, fiberglass has many uses and is recognized as the most important choice in all industries.

Our official website is https://www.china-fiberglass.com/. If you want to know more about fiberglass, you can communicate with us on the website. We will be glad to provide you with high-quality fiberglass, good service, and a competitive price to provide more and better service!

Drywall Tape Self Adhesive Fiberglass Mesh, 2" x 65'

This fiberglass mesh is woven from fiberglass bulk yarn and then treated with alkali-resistant coating. It is widely used in the construction of wall reinforcement, plasterboard, marble and granite. With high strength, temperature preservation properties, water and aging- resistance, this is an important modern construction material

View:76608/11/2018. We help our customer develop a specialized Coated Glass Facer for Gypsum board facer and backer a. This coated fiberglass mat providing a builtin water barrier that stops moisture at the surface. It's also fire proofed meet the standard of ASTM E84-16 . The coated fiberglass mat facer for Gypsum board.

Stitch-Bonded Nonwovens an over

Grip-Rite 48-in x 150-ft EIFS mesh Fiberglass Stucco Netting. Grip-Rite fiberglass EIFS mesh is a woven fiberglass mesh that is an important part of a contentious stucco or EIFS assembly.

Polyester fibres are used in a range of nonwoven filtration media for both air and liquid filtrations. Polyester spunbond fabrics are used in swimming pool and spa filters, municipal sludge

Traditional silica aerogel is a nanostructured material with high specific surface area, high porosity, low density and has excellent heat insulation performance. However, fragility of silica aerogel limits its broad application and its mechanical

BREATHABLE NONWOVEN COMPOSITE . United States Patent Application 20130210304 . Kind Code: A1 . Abstract: Coated nonwoven fabric comprising a nonwoven fabric layer and a