fiberglass matting kit- Suppliers Factory Manufacturers From China

Fiberglass insulation is one of the most popular ways to keep your home warm. Since it's inexpensive, easy to find, and very dense, you can't go wrong with padding your walls. However, it's very squishy, so you might be a little confused about how to cut it. This is a very abrasive material that requires a sharp blade and some safety gear such as a dust mask and glasses. However, with some basic techniques, you can cut insulation board safely and efficiently.

1. Measuring insulating materials

   Choose a piece of plywood that is at least as wide as the fiberglass board. Place it on a flat surface so there is enough room to spread out the fiberglass. The plywood doesn't have to be too big, just make sure it fits underneath the part you're cutting. [
   

   Choose a sturdy piece of material, such as a piece of old plywood

   You can put plywood on the floor for protection.

   Avoid cutting bare surfaces such as concrete.

2. Wear cut-resistant gloves and other protective clothing. Fiberglass insulation is skin irritating, wear long pants and a long-sleeved shirt. Then, put on gloves, and some also wear disposable coveralls to prevent the insulation from spreading onto their clothing.

   If part of your skin is exposed, apply some baby powder on it. The powder prevents glass shards in the insulation from sticking to the skin.

3. Wear a dust mask and safety glasses for protection. A regular N95 cloth dust mask will do just fine, if the mask you're using doesn't cover your eyes, buy separate glasses. Wear safety gear whenever cutting insulation.

   The dust released by the insulation is harmful and can aggravate breathing problems such as asthma.

   If you can, work outside so that dust doesn't settle in your home.

4. Unroll the insulating paper face down. Fiberglass insulation is rolled into a roll. Place the roll over the edge of the plywood. Then, push it through the plywood. Spread out just enough to make the cut you want to make.

   Most insulation has a paper backing on one side. It's usually easier to cut the paper last, and the backing keeps the insulation clean when you unroll it.

5. Use a tape measure to determine where you will cut the insulation. Start by measuring where you plan to install the insulation. Plan to cut the insulation 1 inch (2.5 cm) larger than the insulation on all sides. Because fiberglass insulation is flexible, it can be tucked into tight places. The extra length will help it stay in place.

6. Mark the measurements on the insulator with a permanent marker. Use a tape measure to transfer the measurement to the insulator. Measure along both sides of the insulation, making small marks to indicate where you plan to cut.

   If you roughly cut the insulation to approximate size, you don't need to take any additional measurements. If your goal is a precise cut, you can use a piece of sawdust to make a straight cut in most cases.

  Glass fiber is an organic substance, which itself is not harmful to the human body. But fine fiberglass dust is breathed into a person's lungs. Because glass cannot be absorbed and decomposed at all, it will form deposits for a long time, which will cause occupational diseases similar to silicosis. Although the damage is not fatal, it will affect people's respiratory function. Contact dermatitis often occurs in glass fiber workers, and a few people Skin sensitization occurs, but the fibers themselves have not been proven to be allergens so far.

If it's just pure skin contact, there are generally no other problems, the main reason is that it irritates the skin to a certain extent.

The opposite of Glass fiber is an inorganic non-metallic material with excellent performance. There are many kinds. The advantages are good insulation, strong heat resistance, good corrosion resistance and high mechanical strength, but the disadvantages are brittleness and poor wear resistance. It is made of glass balls or waste glass through high-temperature melting, wire drawing, winding, weaving and other processes. The glass fiber is often used as reinforcing material of composite material, electrical insulation and heat insulation materials, substrate and other national economy fields.

Our company has been engaged in the glass fiber industry for more than ten years, and has rich experience and high-quality products. Welcome to contact us by fiberglass@njefg.com

Fiberglass is a glass material similar to the glass in our windows or the glasses we use to drink our favorite beverages. In modern life, the application of glass fiber can be seen everywhere. People know it differently. The best thing about fiberglass is that it is durable, unbreakable, very strong, and lightweight.

Here is the content list:

• Production of glass fibers

• Application of glass fiber

• Sound-absorbing applications of fiberglass

Production of glass fibers

From the manufacture of glass fibers, the glass is heated until it begins to melt and melt. It is then further forced through the ultrafine pores. This gives us very fine glass filaments, down to the point of being measured in microns. This is the basis of how fiberglass can serve such a variety of uses. These filament threads are flexible and can be molded into a variety of complex shapes for many different applications.

Application of glass fiber

Fiberglass becomes a widely used material in all industries. In addition to being an excellent insulating material, fiberglass is also very cost-effective.

In our daily life, FRP products are used everywhere: subway bodies, auto parts, medical devices, ships, furniture, structural parts for construction and industrial projects, FRP pipes, etc. Why are the surfaces of these FRP products so flat and smooth? The use of fiberglass as the skin material for these products is a key reason.

Sound-absorbing applications of fiberglass

Fiberglass panels are used in building and decorative acoustic panels. After being coated with calcium powder, it is used as the surface layer of thermal insulation materials such as PU and rock wool boards. Fiberglass board has the advantages of being fireproof, waterproof, and mildew proof, smooth surface, uniform fiber dispersion, good weather resistance, and long service life. It is an ideal acoustic decorative material for residents and public areas.

Fiberglass panels are produced with unrivaled formulations and processes, and the thickness of fiberglass panels can reach 8mm to 10mm, and a layer of porous structure gives fiberglass panels a unique combination of sound absorption. At the same time, glass fiberboard has the characteristics of heat preservation, heat preservation, and fire prevention. Coupled with the excellent properties of stiffness, lightweight, bendability, and ease of cutting, further processing, and installation of fiberglass panels are very easy and simple. All these properties make fiberglass panels an ideal material for improving the acoustic environment, reducing heat loss, and making buildings fire-resistant.

NANJING EFG, https://www.china-fiberglass.com/, is a dynamic, creative, experienced, and responsible team. Everyone on the team is committed to providing the best products and services to our customers. Our company has developed a wide range of fiberglass which are tested extensively before leaving the factory to ensure quality. As a professional manufacturer, we specialize in manufacturing the highest quality fiberglass. We have conducted a large number of tests before leaving the factory to ensure the quality. You can consider using our cost-effective products. Thank you for your time! We are looking forward you to coming!

It's fine, lightweight, strong, and above all, it's less brittle – Fiberglass tissue is a need at every construction site. Catering to a diversified set of requirements, fiberglass fleece can be easily molded into any shape. Taking this into consideration, it is easily understandable how fiberglass comes to use every day.

Be it fiberglass reinforced panels or fiberglass fleece, they are durable and long-lasting in every aspect. Here's a glimpse of how and where it is used.

1. Fiberglass Pipe Wrapping Tissue  

Fiberglass Pipe Wrapping Tissue is abundantly used to cover on the surface of steel pipe, being impregnated with bitumen or resin for the anti corrosion of the steel pipes.  Not only this, but fiberglass veil is also an excellent choice for under sink piping.

2. Fiberglass Roofing Tissue

It's excellent, water-resistant, and serves the purpose well – Fiberglass for roofing material is mainly used as a substrate for waterproofing materials. These include waterproofing membrane, asphalt, shingle, and much more. Having excellent waterproofing properties, this is characterized by high tensile strength, remarkable qualities of being water and corrosion resistance, its dimensional stability,  and easy saturation with bitumen. It is also used as reinforcing material of waterproofing painting.

3. Fiberglass Floor Tissues

The primary substrate material of plastic floor and PVC carpet. This might not be the case behind all, but the floor and carpet made with fiberglass floor tissue are more stable, have a smoother appearance, and come in bright colors with convenient laying. The common characteristics include uniformly dispersed fiber, smooth surface, less wool yarn, easy-to-coat PVC, stiffness properties, and folding resistance. Also, excellent dimensional stability is a plus point.

4. Fiberglass Facing Tissue for Wallboards

A Glass Fiber mat for wallboard is produced using the mixture of glass fiber and polyester fiber by the commonly known wet layout process. This excellent composition is the primary reason behind flexibility and stability in everyday use, making the wallboard mats more comfortable and smooth to touch. The polyester fiberglass mat gives the gypsum board remarkable qualities of waterproof, break strength, anti UV, anti-wrinkle, and anti-septic. The common characteristics include strong tensile strength, moisture resistance, mold resistance, and excellent air permeability.

5. Fiberglass Acoustic Boards

Fiberglass acoustic boards are the widely used for sound-absorbing panels that are placed on the walls, ceiling, and other places to absorb the noise and control the sound in a specific area, gives a quiet living environment. Glass Fiber acoustic boards has also features of excellent stiffness, light weight and be bendable, make it be easy mounting. The features of fire proof and formaldehyde make it be a environment friendly material, be suitable for the decoration market.  

Fiberglass is an inorganic non-metallic material with excellent performance. It is made of pyrophyllite, quartz sand, limestone, dolomite, boro site, and boro site as raw materials through high-temperature melting, wire drawing, winding, weaving, and other processes. The diameter of the monofilament is several microns to twenty microns, which is equivalent to 1/20-1/5 of a hair, and each bundle of fiber strands is composed of hundreds or even thousands of monofilaments. Fiberglass is usually used as reinforcing materials in composite materials, electrical insulating materials and thermal insulation materials, circuit substrates, and other fields of the national economy.

Here is the content list:

• Material properties

• Main features of glass fiber

Material properties

Melting point: glass is a kind of amorphous, with no fixed melting point, it is generally considered that its softening point is 500~750℃

Boiling point: about 1000 ℃

Density: 2.4~2.76 g/cm3

When fiberglass is used as a reinforcing material for reinforced plastics, the biggest feature is its high tensile strength. The tensile strength is 6.3 to 6.9 g/d in the standard state and 5.4 to 5.8 g/d in the wet state. Good heat resistance, no effect on strength when the temperature reaches 300 ℃. It has excellent electrical insulation, is an advanced electrical insulation material, and is also used for thermal insulation materials and fire shielding materials. Generally only corroded by concentrated alkali, hydrofluoric acid, and concentrated phosphoric acid.

Main features of glass fiber

Compared with organic fibers, fiberglass has higher temperature resistance, non-combustibility, corrosion resistance, good heat insulation, and sound insulation, high tensile strength, and good electrical insulation. These characteristics make the use of glass fiber far more extensive than other types of fibers, and the development speed is also far ahead.

(1) High tensile strength and small elongation.

(2) High elastic coefficient and good rigidity.

(3) The amount of elongation within the elastic limit is large and the tensile strength is high, so the absorption of the impact energy is large.

(4) Fiberglass is an inorganic fiber, which is non-flammable and has good chemical resistance.

(5) Low water absorption.

(6) The dimensional stability and heat resistance are all good.

(7) Good processability, can be made into different forms of products such as strands, bundles, felts, and woven fabrics.

(8) Transparent and permeable to light.

(9) Good adhesion to resin.

(10) The price is cheap.

(11) It is not easy to burn, and can be melted into glass beads at high temperatures.

NANJING EFG, https://www.china-fiberglass.com/, is a dynamic, creative, experienced, and responsible team. Everyone on the team is committed to providing the best products and services to our customers. Our company has developed a wide range of fiberglass which are tested extensively before leaving the factory to ensure quality. As a professional manufacturer, we specialize in manufacturing the highest quality fiberglass. We have conducted a large number of tests before leaving the factory to ensure the quality. You can consider using our cost-effective products. Thank you for your time!

                                         Why is fleece used in fiberglassing.

1. It is a reinforcing material

In the process of GRG production, gypsum slurry and glass fiber are used alternately, layer by layer. The glass fiber helps to strengthen the firmness of the gypsum block and prevent the gypsum from being scattered after solidification.

2. It has high temperature resistance

It has been tested that when the temperature reaches 300°C, it has no effect on the strength of the glass fiber

3. It has high tensile strength

The tensile strength of glass fiber is 6.3~6.9 g/d in standard state and 5.4~5.8 g/d in wet state.

4.It has good electrical insulation

Glass fiber has excellent electrical insulation and is an advanced electrical insulation material. It is also used in heat insulation materials and fire shielding materials.

5. It is not easy to burn

Glass fiber can be melted into glass beads at high temperature, which meets the requirements of fire prevention and control in the construction industry.

6. It has good sound insulation

The combination of glass fiber and gypsum can achieve a good sound insulation effect.

7. It’s cheap

Regardless of the industry, cost control is the most important link, and products with high quality and low price will definitely be favored.

Well, the above are the seven advantages of why glass fiber can be widely used in the construction industry. Glass Fiber is a very good substitute for metal materials.

These different characteristics make APP, and SBS membranes have different advantages regarding how they are used. APP membranes are used more often on smaller roofing areas

Fiberglass Tissue for gypsum board on sale manufacturers, find details about Fiberglass Tissue for gypsum board manufacturers, supplier and wholesaler

What is Fiberglass Roofing Fleece Tissue for FRP Products, Fiberglass Tissue manufacturers

Your cars starter battery is most likely either a flooded lead acid or an AGM battery, both of which are rechargeable battery types. ???? ???????????? LiFePO4 ?????? Portable Power Station

Vacuum Packed. Published: Sep 30, 2009. While trucking seven 30-gallon garbage bags of once mouse-infested fiberglass insulation to the local transfer station, it occurred to me that there must be ...

We find 600 products about fiberglass board from 214 manufacturers

Summary. Fiberglass filter tissue is made by advanced wet-formed technology, the main material is E-glass chopped strand and environmentally friendly binder, it is mainly used for the

Also, all of our workers are experienced in printing subject for Polyester Spunbond Nonwoven Fabric, Neck Wrap Heating Pad , Filters 0.3 Micron Size , Heater Pad , Felt Pad For Mattress . If you pursuit the Hi-quality, Hi-stable, Competitive price parts, company name is your best choice! The product will supply to all over the world, such as ...