fiberglass reinforced adhesive tape- China Manufacturers Suppliers Factory

Fiberglass insulation is one of the most popular ways to keep your home warm. Since it's inexpensive, easy to find, and very dense, you can't go wrong with padding your walls. However, it's very squishy, so you might be a little confused about how to cut it. This is a very abrasive material that requires a sharp blade and some safety gear such as a dust mask and glasses. However, with some basic techniques, you can cut insulation board safely and efficiently.

1. Measuring insulating materials

   Choose a piece of plywood that is at least as wide as the fiberglass board. Place it on a flat surface so there is enough room to spread out the fiberglass. The plywood doesn't have to be too big, just make sure it fits underneath the part you're cutting. [
   

   Choose a sturdy piece of material, such as a piece of old plywood

   You can put plywood on the floor for protection.

   Avoid cutting bare surfaces such as concrete.

2. Wear cut-resistant gloves and other protective clothing. Fiberglass insulation is skin irritating, wear long pants and a long-sleeved shirt. Then, put on gloves, and some also wear disposable coveralls to prevent the insulation from spreading onto their clothing.

   If part of your skin is exposed, apply some baby powder on it. The powder prevents glass shards in the insulation from sticking to the skin.

3. Wear a dust mask and safety glasses for protection. A regular N95 cloth dust mask will do just fine, if the mask you're using doesn't cover your eyes, buy separate glasses. Wear safety gear whenever cutting insulation.

   The dust released by the insulation is harmful and can aggravate breathing problems such as asthma.

   If you can, work outside so that dust doesn't settle in your home.

4. Unroll the insulating paper face down. Fiberglass insulation is rolled into a roll. Place the roll over the edge of the plywood. Then, push it through the plywood. Spread out just enough to make the cut you want to make.

   Most insulation has a paper backing on one side. It's usually easier to cut the paper last, and the backing keeps the insulation clean when you unroll it.

5. Use a tape measure to determine where you will cut the insulation. Start by measuring where you plan to install the insulation. Plan to cut the insulation 1 inch (2.5 cm) larger than the insulation on all sides. Because fiberglass insulation is flexible, it can be tucked into tight places. The extra length will help it stay in place.

6. Mark the measurements on the insulator with a permanent marker. Use a tape measure to transfer the measurement to the insulator. Measure along both sides of the insulation, making small marks to indicate where you plan to cut.

   If you roughly cut the insulation to approximate size, you don't need to take any additional measurements. If your goal is a precise cut, you can use a piece of sawdust to make a straight cut in most cases.

Fiberglass floor paper products are the base material for vinyl floors and decorative wallpapers. The floor and wallpaper made of this product have the characteristics of good stability, smooth appearance, bright color, and convenient laying. It is widely used as decoration materials in public entertainment places such as hospitals, schools, libraries, etc. It can also be used in high-grade floors and walls such as hotels, shopping malls, conference halls, office buildings, and residences.

Here is the content list:

• Features of the fiberglass floor papers we sell
  

• How can we provide you with products?

Features of the fiberglass floor papers we sell

The fiberglass floor paper we sell is evenly dispersed, with a smooth surface, less wool, and easy-to-apply PVC. It is also stiff, resistant to folding, not easily deformed, and has good dimensional stability.

The PVC floor produced with fiberglass floor paper has the characteristics of good stability, smooth appearance, bright color, and convenient installation. PVC floor is a decorative material widely used in hospitals, schools, libraries, airports, and other public places.

How can we provide you with products?

Our products are packaged in standard export packaging for shipping.

1. Roll packing: PE plastic film.

2. Pallet Packing: Pallets should not be stacked in more than 2 layers.

3. The tray is free of fumigation, and a fumigation certificate can be provided.

Our fiberglass floor paper products should be stored in a dry, ventilated, rain-proof place with a temperature of 5°C to 35°C and a humidity of 35% to 65%. It is recommended to keep the intact packaging when not in use to avoid moisture.

If customers need specific unit weight, tensile strength, roll width, and roll length, NANJING EFG can produce according to customer requirements and provide tailor-made services to customers from different countries.

Our fiberglass floor paper products are loaded using standard export loading.

NANJING EFG has delivered materials to US, EU, Middle East, North Africa, South Africa, and Asia customers with guaranteed quality and good feedback. With rich export experience and technical support, NANJING EFG welcomes cooperation with customers from all over the world.

The materials are packed in the factory, then shipped to the seaport, and finally shipped to the customer's port by MSK, MSC, CMA, COSCO, YANGMING, APL, etc.

【Payment method】 LC, T/T, CAD, PAYPAL, WESTERN UNION, ETC.

【After-sale service】

Nanjing EFG CO., LTD tracks the goods of each shipment until the customer uses the material, and is ready to provide any assistance to the customer's needs.

【Technical Support】

If customers encounter any technical problems, Nanjing EFG CO., LTD will provide relevant knowledge to help customers find the best solution, and send technicians to customers' factories for guidance when necessary.

If you are interested in purchasing fiberglass, visit our website: https://www.china-fiberglass.com/to get more professional information about fiberglass. We will welcome you with high-quality products and good service as well as low prices! To provide comprehensive technical support to our customers, we will provide technical and other related information on time upon request.

The glass fiber black felt adopts a thermosetting resin-based environmentally friendly formula adhesive to tightly bond the composite fibers, with good color fixation, high strength, wear resistance, and effective control of fiber scattering. Black fiberglass felt has excellent flame retardant, sound absorption and noise reduction, and thermal insulation effect. Anti-fouling and water-repellent, effectively avoid the growth and reproduction of various microorganisms, anti-bacterial and anti-mildew. Especially suitable for high-speed, high-speed rail sound-absorbing barriers, perforated sound-absorbing panels veneer, good light absorption, and zero reflection.

Here is the content list:

• The role of Black fiberglass

• Advantages and applications of Black fiberglass felt

• Please rest assured to choose NANJING EFG

The role of Black fiberglass

Black fiberglass is compounded on a glass wool board, which is a special material for heat preservation, sound absorption, and noise reduction. It acts on the lining of the glass wool air duct, absorbs the noise of the air duct system, reduces the loss of heat and cold on the air duct wall, and can meet the requirements of reducing energy consumption. requirements, greatly improving the indoor acoustic environment quality. It is especially suitable for environments with high mute requirements to improve sound quality and speech intelligibility. Such as high-end hotels, office buildings, clubs, and so on.

Advantages and applications of Black fiberglass felt

1.Antibacterial and mildew proof, the fiber is not easy to fall off.

2. Flame retardant.

3. Sound absorption, noise reduction, sound insulation, and thermal insulation performance.

4. Waterproof, oilproof, antifouling.

Used as high-speed rail, high-speed rail with sound-absorbing barriers, and perforated sound-absorbing panel veneer. Black fiberglass felt can also be used as air conditioner insulation panel veneer/glass wool panel veneer/ceiling back panel/solar flat panel heat collector panel veneer.

Please rest assured to choose NANJING EFG

As an expert in glass fiber and non-woven materials, NANJING EFG started in 2006 and established the vision of "building an internationally renowned brand" in the field of glass fiber and non-woven materials.

Every employee of NANJING EFG incorporates this belief into their daily work and life. When you work with NANJING EFG, you will find that you are working with a professional team whose service is positive and efficient, with consistent quality and an unforgettable reputation.

NANJING EFG was established to meet various needs of wallboard, thermal insulation, reinforcement, insulation, filtration, surface treatment, decoration, paving, waterproofing, glass fiber reinforced plastic, electrical and electrical, etc., with fiberglass and non-glass fiber as the base material for woven materials. NANJING EFG has a well-trained and experienced technical team focused on providing "tailor-made" product and service solutions. NANJING EFG ensures the best product performance for your business at the lowest total cost. NANJING EFG's professional service team will provide you with high-quality products and efficient services on time.

If you are interested in purchasing fiberglass, visit our website: https://www.china-fiberglass.com/to get more professional information about fiberglass. We will welcome you with high-quality products and good service as well as low prices! To provide comprehensive technical support to our customers, we will provide technical and other related information promptly upon request.

Fiberglass is an inorganic non-metallic material with excellent performance. It is made of pyrophyllite, quartz sand, limestone, dolomite, boro site, and boro site as raw materials through high-temperature melting, wire drawing, winding, weaving, and other processes. The diameter of the monofilament is several microns to twenty microns, which is equivalent to 1/20-1/5 of a hair, and each bundle of fiber strands is composed of hundreds or even thousands of monofilaments. Fiberglass is usually used as reinforcing materials in composite materials, electrical insulating materials and thermal insulation materials, circuit substrates, and other fields of the national economy.

Here is the content list:

• Material properties

• Main features of glass fiber

Material properties

Melting point: glass is a kind of amorphous, with no fixed melting point, it is generally considered that its softening point is 500~750℃

Boiling point: about 1000 ℃

Density: 2.4~2.76 g/cm3

When fiberglass is used as a reinforcing material for reinforced plastics, the biggest feature is its high tensile strength. The tensile strength is 6.3 to 6.9 g/d in the standard state and 5.4 to 5.8 g/d in the wet state. Good heat resistance, no effect on strength when the temperature reaches 300 ℃. It has excellent electrical insulation, is an advanced electrical insulation material, and is also used for thermal insulation materials and fire shielding materials. Generally only corroded by concentrated alkali, hydrofluoric acid, and concentrated phosphoric acid.

Main features of glass fiber

Compared with organic fibers, fiberglass has higher temperature resistance, non-combustibility, corrosion resistance, good heat insulation, and sound insulation, high tensile strength, and good electrical insulation. These characteristics make the use of glass fiber far more extensive than other types of fibers, and the development speed is also far ahead.

(1) High tensile strength and small elongation.

(2) High elastic coefficient and good rigidity.

(3) The amount of elongation within the elastic limit is large and the tensile strength is high, so the absorption of the impact energy is large.

(4) Fiberglass is an inorganic fiber, which is non-flammable and has good chemical resistance.

(5) Low water absorption.

(6) The dimensional stability and heat resistance are all good.

(7) Good processability, can be made into different forms of products such as strands, bundles, felts, and woven fabrics.

(8) Transparent and permeable to light.

(9) Good adhesion to resin.

(10) The price is cheap.

(11) It is not easy to burn, and can be melted into glass beads at high temperatures.

NANJING EFG, https://www.china-fiberglass.com/, is a dynamic, creative, experienced, and responsible team. Everyone on the team is committed to providing the best products and services to our customers. Our company has developed a wide range of fiberglass which are tested extensively before leaving the factory to ensure quality. As a professional manufacturer, we specialize in manufacturing the highest quality fiberglass. We have conducted a large number of tests before leaving the factory to ensure the quality. You can consider using our cost-effective products. Thank you for your time!

    Fiberglass membranes are manufactured from 100% borosilicate glass fibers and include binder-free, chemically inert and binder-containing types. The purpose of adding binder is to enhance the mechanical strength of the glass fiber membrane. It is mainly used to filter coarse particles (such as macromolecular substances, dust). In order to avoid chemical reactions with the filtered substance, glass with inorganic binder is used when filtering organic substances. Fiber membrane, choose glass fiber membrane with organic binder when filtering inorganic substances. This depth filter membrane has the characteristics of fast flow rate, large load capacity and extremely fine retained particles, which can reach the range of submicron particles. The glass fiber membrane can withstand a temperature of 500°C, and can be used for specific gravity analysis and high-temperature gas filtration that require ignition.

    Grade GF/A: For high-efficiency routine filtration, including waste water pollution detection, for filtered water, algae and bacterial culture, food analysis, protein filtration and radioimmunoassay of weak beta emitters, recommended for particulate matter in air pollution monitoring Gravimetry, stack sampling and adsorption, etc.

   Grade GF/B: Used to retain fine particles, fast flow rate. Especially suitable for sample processing with high suspended fine particles in liquid clarification or particle quantification. It can be used for pre-filtration of fine particles before membrane filtration, as a stationary phase in LSC (liquid-solid chromatography), and for protein binding.

    Grade GF/C: Standard filter paper for collecting suspended solids in drinking water, natural water and industrial wastewater. Quickly and efficiently clarifies aqueous solutions containing small to moderately fine particles. Widely used in cell harvesting, liquid scintillation counting and binding assays when higher loads are required.

    Grade GF/D: A common membrane pre-filtration material that can be used with GF/B to provide a very effective graded pre-filtration protection for the membrane.

    Grade GF/F: Commonly used for DNA binding, adsorption and purification, protein binding, and the effect of filtering fine precipitated proteins is obvious. The combination    of GF/F and GF/D can be used as a pre-filter membrane to purify extremely difficult to clarify biochemical solutions, fluids and nucleic acids .

   Grade GF10: Commonly used in roll filter membranes in automatic air filtration devices.

   If you want to know more details, you can contact on fiberglass@njefg.com.

The need of every household and a must in every building construction, fiberglass tissue has been the talk of the town for ages. But what does it do? What is it used for? Let us help you put a full stop to your pondering! Fiberglass fleece is a fine matting that is similar to tissue paper. It is produced from glass fiber, be widely used in FRP composite surface applications and ensures smoothness and a clean look of colour to the surface. That isn't it; it also helps thermal resistance and ensures the durability of the product.

Fiberglass: Uses

Having diversified uses, this fiberglass veil acts as an excellent fiberglass pipe wrapping tissue. It is used for pipe insulation to ensure the correct temperature of water flowing through. Secondly, it is also a fantastic choice for roofing tissue. It is used to produce bitumen membrane or bitumen shingles – whatever serves the purpose well. Moreover, it is also used as a fiberglass floor tissue that produces PVC floors.  Apart from this, this is also an incredible choice for creating PVC carpets with long-lasting durability.

Coming over to its uses as a surface tissue, this is a go-to choice for many builders. Wondering why? As it is used for the surface treatment of Fiber Reinforced Plastic products. There's more to it – the fiberglass facing tissue can be used for internal wall decoration without worrying about leakage issues. Talking about wallboards and wallpaper choices, this fiberglass wallpaper and fiberglass facing tissue for wallboards are abundantly used to cover wallboard and internal wall decoration. Covering up acoustic boards is an issue in most households as well as buildings. This serves that purpose well too. Go for Fiberglass Acoustic Mat as it can be easily used as a surface layer of the acoustic board. The reason being that it is coated with CaC03 compound through a particular treatment.

Further, over to its battery use, this fiberglass battery separator tissue can be used as a lead-acid battery separator. Also, the commonly available black tissue is an excellent choice for thermal insulation. It can be for different materials; it serves as an insulation tape or insulation board, both. Lastly, fiberglass yellow tissue is also a good choice. It is widely being used as thermal insulation material to cover up the surface of the mineral wool board.

Glass Fiber Mat: Qualities

· Cost-Effective

· Corrosion Resistant

· Excellent Strength

· It comes with an amazing strength to weight ratio

· Has high heat distortion temperature

· The incredible quality of being electrically non – conductive

· Ability to be moulded to precise tolerances

Fiberglass is a glass material similar to the glass in our windows or the glasses we use to drink our favorite beverages. In modern life, the application of glass fiber can be seen everywhere. People know it differently. The best thing about fiberglass is that it is durable, unbreakable, very strong, and lightweight.

Here is the content list:

• Production of glass fibers

• Application of glass fiber

• Sound-absorbing applications of fiberglass

Production of glass fibers

From the manufacture of glass fibers, the glass is heated until it begins to melt and melt. It is then further forced through the ultrafine pores. This gives us very fine glass filaments, down to the point of being measured in microns. This is the basis of how fiberglass can serve such a variety of uses. These filament threads are flexible and can be molded into a variety of complex shapes for many different applications.

Application of glass fiber

Fiberglass becomes a widely used material in all industries. In addition to being an excellent insulating material, fiberglass is also very cost-effective.

In our daily life, FRP products are used everywhere: subway bodies, auto parts, medical devices, ships, furniture, structural parts for construction and industrial projects, FRP pipes, etc. Why are the surfaces of these FRP products so flat and smooth? The use of fiberglass as the skin material for these products is a key reason.

Sound-absorbing applications of fiberglass

Fiberglass panels are used in building and decorative acoustic panels. After being coated with calcium powder, it is used as the surface layer of thermal insulation materials such as PU and rock wool boards. Fiberglass board has the advantages of being fireproof, waterproof, and mildew proof, smooth surface, uniform fiber dispersion, good weather resistance, and long service life. It is an ideal acoustic decorative material for residents and public areas.

Fiberglass panels are produced with unrivaled formulations and processes, and the thickness of fiberglass panels can reach 8mm to 10mm, and a layer of porous structure gives fiberglass panels a unique combination of sound absorption. At the same time, glass fiberboard has the characteristics of heat preservation, heat preservation, and fire prevention. Coupled with the excellent properties of stiffness, lightweight, bendability, and ease of cutting, further processing, and installation of fiberglass panels are very easy and simple. All these properties make fiberglass panels an ideal material for improving the acoustic environment, reducing heat loss, and making buildings fire-resistant.

NANJING EFG, https://www.china-fiberglass.com/, is a dynamic, creative, experienced, and responsible team. Everyone on the team is committed to providing the best products and services to our customers. Our company has developed a wide range of fiberglass which are tested extensively before leaving the factory to ensure quality. As a professional manufacturer, we specialize in manufacturing the highest quality fiberglass. We have conducted a large number of tests before leaving the factory to ensure the quality. You can consider using our cost-effective products. Thank you for your time! We are looking forward you to coming!

It's fine, lightweight, strong, and above all, it's less brittle – Fiberglass tissue is a need at every construction site. Catering to a diversified set of requirements, fiberglass fleece can be easily molded into any shape. Taking this into consideration, it is easily understandable how fiberglass comes to use every day.

Be it fiberglass reinforced panels or fiberglass fleece, they are durable and long-lasting in every aspect. Here's a glimpse of how and where it is used.

1. Fiberglass Pipe Wrapping Tissue  

Fiberglass Pipe Wrapping Tissue is abundantly used to cover on the surface of steel pipe, being impregnated with bitumen or resin for the anti corrosion of the steel pipes.  Not only this, but fiberglass veil is also an excellent choice for under sink piping.

2. Fiberglass Roofing Tissue

It's excellent, water-resistant, and serves the purpose well – Fiberglass for roofing material is mainly used as a substrate for waterproofing materials. These include waterproofing membrane, asphalt, shingle, and much more. Having excellent waterproofing properties, this is characterized by high tensile strength, remarkable qualities of being water and corrosion resistance, its dimensional stability,  and easy saturation with bitumen. It is also used as reinforcing material of waterproofing painting.

3. Fiberglass Floor Tissues

The primary substrate material of plastic floor and PVC carpet. This might not be the case behind all, but the floor and carpet made with fiberglass floor tissue are more stable, have a smoother appearance, and come in bright colors with convenient laying. The common characteristics include uniformly dispersed fiber, smooth surface, less wool yarn, easy-to-coat PVC, stiffness properties, and folding resistance. Also, excellent dimensional stability is a plus point.

4. Fiberglass Facing Tissue for Wallboards

A Glass Fiber mat for wallboard is produced using the mixture of glass fiber and polyester fiber by the commonly known wet layout process. This excellent composition is the primary reason behind flexibility and stability in everyday use, making the wallboard mats more comfortable and smooth to touch. The polyester fiberglass mat gives the gypsum board remarkable qualities of waterproof, break strength, anti UV, anti-wrinkle, and anti-septic. The common characteristics include strong tensile strength, moisture resistance, mold resistance, and excellent air permeability.

5. Fiberglass Acoustic Boards

Fiberglass acoustic boards are the widely used for sound-absorbing panels that are placed on the walls, ceiling, and other places to absorb the noise and control the sound in a specific area, gives a quiet living environment. Glass Fiber acoustic boards has also features of excellent stiffness, light weight and be bendable, make it be easy mounting. The features of fire proof and formaldehyde make it be a environment friendly material, be suitable for the decoration market.  

Looking for stucco fiberglass mesh factory direct sale? You can buy factory price stucco fiberglass mesh from a great list of reliable China stucco fiberglass mesh manufacturers, suppliers, traders or plants verified by a third-party inspector. Source with confidence.

cotton Polyester Nonwoven for paving on sale manufacturers, find details about cotton Polyester Nonwoven for paving manufacturers, supplier and wholesaler

Spunbond Nonwoven Fabric for sale, new Breathable 25gsm Bacteriostasis Graphene Nonwoven Fabric of Xian Galaxy Rising Industrial Co., Ltd. from China. Sign In

Fiberglass has other properties which make it a lesser choice than mineral wool as soundproofing insulation material. Over time fiberglass can become compressed or lose its form, reducing its sound absorption ability. The same thing can happen to its thermal protection properties, normally quite good but subject to erosion over time.

Application for roofing fiberglass mesh tape

The raw materials of the GRP sheet are typi

Coated Tissue for Gypsum Sheathing. The company specializes in the research, production and sales of glass fiber related products, which are sold in more than 70 countries and regions around the world, Support wholesale and customization. ... Fiberglass assembled roving Fiberglass direct roving Fiberglass AR roving Fiberglass Multi-end Roving ...

Thermomechani