glass fiber stitched mat- China Manufacturers Suppliers Factory

Fiberglass insulation is one of the most popular ways to keep your home warm. Since it's inexpensive, easy to find, and very dense, you can't go wrong with padding your walls. However, it's very squishy, so you might be a little confused about how to cut it. This is a very abrasive material that requires a sharp blade and some safety gear such as a dust mask and glasses. However, with some basic techniques, you can cut insulation board safely and efficiently.

1. Measuring insulating materials

   Choose a piece of plywood that is at least as wide as the fiberglass board. Place it on a flat surface so there is enough room to spread out the fiberglass. The plywood doesn't have to be too big, just make sure it fits underneath the part you're cutting. [
   

   Choose a sturdy piece of material, such as a piece of old plywood

   You can put plywood on the floor for protection.

   Avoid cutting bare surfaces such as concrete.

2. Wear cut-resistant gloves and other protective clothing. Fiberglass insulation is skin irritating, wear long pants and a long-sleeved shirt. Then, put on gloves, and some also wear disposable coveralls to prevent the insulation from spreading onto their clothing.

   If part of your skin is exposed, apply some baby powder on it. The powder prevents glass shards in the insulation from sticking to the skin.

3. Wear a dust mask and safety glasses for protection. A regular N95 cloth dust mask will do just fine, if the mask you're using doesn't cover your eyes, buy separate glasses. Wear safety gear whenever cutting insulation.

   The dust released by the insulation is harmful and can aggravate breathing problems such as asthma.

   If you can, work outside so that dust doesn't settle in your home.

4. Unroll the insulating paper face down. Fiberglass insulation is rolled into a roll. Place the roll over the edge of the plywood. Then, push it through the plywood. Spread out just enough to make the cut you want to make.

   Most insulation has a paper backing on one side. It's usually easier to cut the paper last, and the backing keeps the insulation clean when you unroll it.

5. Use a tape measure to determine where you will cut the insulation. Start by measuring where you plan to install the insulation. Plan to cut the insulation 1 inch (2.5 cm) larger than the insulation on all sides. Because fiberglass insulation is flexible, it can be tucked into tight places. The extra length will help it stay in place.

6. Mark the measurements on the insulator with a permanent marker. Use a tape measure to transfer the measurement to the insulator. Measure along both sides of the insulation, making small marks to indicate where you plan to cut.

   If you roughly cut the insulation to approximate size, you don't need to take any additional measurements. If your goal is a precise cut, you can use a piece of sawdust to make a straight cut in most cases.

Fiberglass is an inorganic non-metallic material with excellent performance. It is made of pyrophyllite, quartz sand, limestone, dolomite, boro site, and boro site as raw materials through high-temperature melting, wire drawing, winding, weaving, and other processes. The diameter of the monofilament is several microns to twenty microns, which is equivalent to 1/20-1/5 of a hair, and each bundle of fiber strands is composed of hundreds or even thousands of monofilaments. Fiberglass is usually used as reinforcing materials in composite materials, electrical insulating materials and thermal insulation materials, circuit substrates, and other fields of the national economy.

Here is the content list:

• Material properties

• Main features of glass fiber

Material properties

Melting point: glass is a kind of amorphous, with no fixed melting point, it is generally considered that its softening point is 500~750℃

Boiling point: about 1000 ℃

Density: 2.4~2.76 g/cm3

When fiberglass is used as a reinforcing material for reinforced plastics, the biggest feature is its high tensile strength. The tensile strength is 6.3 to 6.9 g/d in the standard state and 5.4 to 5.8 g/d in the wet state. Good heat resistance, no effect on strength when the temperature reaches 300 ℃. It has excellent electrical insulation, is an advanced electrical insulation material, and is also used for thermal insulation materials and fire shielding materials. Generally only corroded by concentrated alkali, hydrofluoric acid, and concentrated phosphoric acid.

Main features of glass fiber

Compared with organic fibers, fiberglass has higher temperature resistance, non-combustibility, corrosion resistance, good heat insulation, and sound insulation, high tensile strength, and good electrical insulation. These characteristics make the use of glass fiber far more extensive than other types of fibers, and the development speed is also far ahead.

(1) High tensile strength and small elongation.

(2) High elastic coefficient and good rigidity.

(3) The amount of elongation within the elastic limit is large and the tensile strength is high, so the absorption of the impact energy is large.

(4) Fiberglass is an inorganic fiber, which is non-flammable and has good chemical resistance.

(5) Low water absorption.

(6) The dimensional stability and heat resistance are all good.

(7) Good processability, can be made into different forms of products such as strands, bundles, felts, and woven fabrics.

(8) Transparent and permeable to light.

(9) Good adhesion to resin.

(10) The price is cheap.

(11) It is not easy to burn, and can be melted into glass beads at high temperatures.

NANJING EFG, https://www.china-fiberglass.com/, is a dynamic, creative, experienced, and responsible team. Everyone on the team is committed to providing the best products and services to our customers. Our company has developed a wide range of fiberglass which are tested extensively before leaving the factory to ensure quality. As a professional manufacturer, we specialize in manufacturing the highest quality fiberglass. We have conducted a large number of tests before leaving the factory to ensure the quality. You can consider using our cost-effective products. Thank you for your time!

Fiberglass has a great application in the field of decoration. Fiberglass floor towels and fiberglass carpet towels are examples, so when you cut a PVC floor or PVC carpet, you will find a thin layer of glass fiber in the middle of the PVC. The glass fiber makes the surface of the PVC floor flat and effectively avoids the deformation of the PVC floor and carpet. This is why PVC floors and carpets with a fiberglass core do not deform and blister in flooring applications.

Here is the content list:

• Characteristics of fiberglass

• Various applications of glass fibers

Characteristics of fiberglass

1. The fiberglass is uniformly dispersed and the surface is smooth

2. Excellent bonding performance with coatings

3. Waterproof and weather resistance, long service life

Various applications of glass fibers

1.The glass fiber veneer paper directly covers the surface of the inner wall, making the wall smooth and textured. Fiberglass joint tapes are used as joint tapes for wall panel joints and wall crack/hole repair. Coated fiberglass mats are coated with a CaCO3 compound on the fiberglass mats. The coated fiberglass mat is used as a decoration mat to directly cover the uneven wall surface to avoid falling off of the decoration layer. Coated fiberglass mats are a quick and easy solution for updating walls.

2. Fiberglass filter media is also widely used in the field of air filtration. One of the applications is to use glass fiber filter paper as the skeleton layer, and the primary filter layer is laminated with glass fiber paper. The laminate is the functional part of the filter element. The second filter application is the use of glass fiber filter paper towels in environmental engineering to chemically remove VOC gases.

3. Fiberglass mat, polyester fiberglass mat, and CaCo3-coated fiberglass are ideal wallboard covering materials. Using these materials instead of kraft paper to cover the surface of the wallboard can effectively improve the breaking strength of the wallboard, and at the same time endow the wallboard with excellent characteristics such as waterproof, fireproof, heat insulation, and mildew resistance. Proven, scratch-resistant, etc.

4. Fiberglass battery separator paper towel is the first choice for all battery rooms, used as a separator for lead-acid batteries.

5. Glass fiber black paper towels, glass fiber yellow paper towels, and coated glass fiber mats are used as insulation materials for the surface of insulation boards such as mineral wool boards and polyurethane boards, giving insulation boards excellent breaking strength, and other functional properties, such as Fire and waterproof.

6. The fiberglass roof is used as the core material of the bituminous membrane. Also used as reinforcement for waterproof coatings. Asphalt can quickly impregnate fiberglass roof tissue, which retains and reinforces asphalt.

All in all, fiberglass has many uses and is recognized as the most important choice in all industries.

Our official website is https://www.china-fiberglass.com/. If you want to know more about fiberglass, you can communicate with us on the website. We will be glad to provide you with high-quality fiberglass, good service, and a competitive price to provide more and better service!

Fiberglass is not made of glass.

Glass fiber is made of pyrophyllite, quartz sand, limestone, dolomite, boronite, and boronite as raw materials through high-temperature melting, wire drawing, winding, weaving and other processes. Its main components are silica, alumina, calcium oxide, boron oxide, magnesium oxide, sodium oxide, etc. According to the alkali content in the glass, it can be divided into alkali-free glass fibers (0% to 2% sodium oxide, which belongs to aluminum Borosilicate glass), medium-alkali glass fiber (sodium oxide 8% to 12%, which belongs to boron-containing or boron-free soda-lime silicate glass) and high-alkali glass fiber (more than 13% sodium oxide, which belongs to soda-calcium silicate glass) silicate glass).

Fiberglass is an inorganic non-metallic material with excellent performance. There are many kinds. Its advantages are good insulation, strong heat resistance, good corrosion resistance and high mechanical strength. Difference. The diameter of its monofilament is several microns to more than 20 microns, which is equivalent to 1/20-1/5 of a hair, and each bundle of fiber precursors is composed of hundreds or even thousands of monofilaments. The glass fiber is often used as reinforcing material of composite material, electrical insulation and heat insulation materials, substrate and other national economy fields.

                                         Why is fleece used in fiberglassing.

1. It is a reinforcing material

In the process of GRG production, gypsum slurry and glass fiber are used alternately, layer by layer. The glass fiber helps to strengthen the firmness of the gypsum block and prevent the gypsum from being scattered after solidification.

2. It has high temperature resistance

It has been tested that when the temperature reaches 300°C, it has no effect on the strength of the glass fiber

3. It has high tensile strength

The tensile strength of glass fiber is 6.3~6.9 g/d in standard state and 5.4~5.8 g/d in wet state.

4.It has good electrical insulation

Glass fiber has excellent electrical insulation and is an advanced electrical insulation material. It is also used in heat insulation materials and fire shielding materials.

5. It is not easy to burn

Glass fiber can be melted into glass beads at high temperature, which meets the requirements of fire prevention and control in the construction industry.

6. It has good sound insulation

The combination of glass fiber and gypsum can achieve a good sound insulation effect.

7. It’s cheap

Regardless of the industry, cost control is the most important link, and products with high quality and low price will definitely be favored.

Well, the above are the seven advantages of why glass fiber can be widely used in the construction industry. Glass Fiber is a very good substitute for metal materials.

Fiberglass is a glass material similar to the glass we have in our windows or the glass we drink our favorite slush in. But the best part about glass fiber is that it's durable, it's less brittle, it's very strong, and it's lightweight.

Starting it off with the manufacturing of fiberglass fleece, glass is heated up till the point that it starts to melt and is molten. It is then further on forced through superfine holes. This, in turn, gives us glass filaments that are very thin, thin to the extent that they are measured in microns. Interesting enough! This point is the fundamental base for how the fiberglass veil caters to such a diversified set of uses. These filament threads are flexible and can be molded into various complex shapes for many different applications.

Let us have a glimpse into the applications of glass fiber mats in various sectors of society.

Understanding how Fibre de Verre is durable, exceptionally safe, and offers high thermal insulation, fiberglass filter tissue is a widely preferred material in all industries. The main plus point is that apart from being an excellent insulation material, it is very cost-efficient. Here is its use in different sectors:

- Surface treatment of FRP products. In our daily life, you are using Fiberglass Reinforced Plastic (FRP) products anywhere: Body of metro, car parts, Medical instruments, boats, furniture, structure parts of buildings and industrial projects, FRP pipes...... Do you know why the surface of these FRP products are perfectly even and smooth ?  Fiberglass surface tissue is used as the surface material of these FPR products are the key reason.

- PVC floor and Carpet: Fiberglass Tissue have a large scale of application in the field of decoration. Fiberglass floor tissue and fiberglass carpet tissue are used as the stabilize layer of the PVC floor and PVC carpet , So do not surprise that when you cut the PVC floor or PVC carpet, you will find that in the middle of the PVC these is a thin core layer which is fiberglass layer. The fiberglass layer absorb the PVC quickly and give the of PVC floor an even surface, efficiently avoid deforming of PVC floor and carpet. That’s why the PVC floor and carpet which used fiberglass as core layer will not be find deforming and bubble in the floor application.

-  Acoustic panel:  Fiberglass Board is produced with unparalleled formula and process, the fiberglass board can reach the thickness 8mm till 10mm, the one layer polyporous structure make the fiberglass board has unique combination of abuse resistance and sound absorption. At the same time, the fiberglass Board has the features of heat reservation, thermal insulation and fire-proofing. Adding the excellent features of stiffness, light weight, bendable and easy cutting, the fiberglass board is very easy and simple to be further processed and installed. All these features make the fiberglass board an ideal material to improve the acoustic environment, decrease the loss of heat and keep the building safe from fire.

- Internal wall decoration: Fiberglass facing tissue is used to cover on the surface of internal wall directly, which give the wall even surface and quality feeling. Fiberglass non-woven tape is used as joint tape for the wall boards joint connection and crack/hole  repair of the wall.  Coated fiberglass mat is coating the CaCO3 compound on the fiberglass mat.  The coated fiberglass mat is used as redecoration mat to cover on the surface of uneven wall directly, avoided removing the decoration layer. The coated fiberglass mat is a fast and easy solution to renew the wall.

- Filtration:  Fiberglass filter tissue is widely used in the field of air filtration. One of the  applications is to use the fiberglass filter tissue as frame layer and primary filter layer to attach with fiberglass paper. The laminated material is the functional part of the filter element.  The second filtration application is to use the fiberglass filter tissue in the environmental project to remove the VOC gas by chemical method.

- Wall boards. Fiberglass mat, polyester fiberglass mat and CaCo3 Coated fiberglass are idea covering material of wall boards. Use these material to replace the craft paper to cover on the surface of wall boards can efficiently increase the break strength of the wall boards, at same time it can give the wall boards excellent features such as water proof, fire proof, thermal insulation, mildew proof, scratch resistant and so on.

- Batteries: Fiberglass Battery Separator tissue is the go-to choice at all battery houses for being used as a separator of lead-acid batteries.

- Insulation: Fiberglass Black Tissue , Fiberglass Yellow Tissues and coated fiberglass mat are used as thermal insulation material to be use on the surface of insulation boards such as mineral wool boards and polyurethane boards, give the insulation board excellent break strength and other functional features such as fireproof and waterproof.

     -    Waterproof :  Fiberglass roofing tissue is used as core material of bitumen membrane. Also be used as reinforce material of waterproof painting. Bitumen can impregnate the fiberglass roofing tissue quickly, fiberglass roofing tissue hold and reinforce the bitumen.

All in all, fiberglass has many uses and is known to be the most substantial choice in all industries.

The need of every household and a must in every building construction, fiberglass tissue has been the talk of the town for ages. But what does it do? What is it used for? Let us help you put a full stop to your pondering! Fiberglass fleece is a fine matting that is similar to tissue paper. It is produced from glass fiber, be widely used in FRP composite surface applications and ensures smoothness and a clean look of colour to the surface. That isn't it; it also helps thermal resistance and ensures the durability of the product.

Fiberglass: Uses

Having diversified uses, this fiberglass veil acts as an excellent fiberglass pipe wrapping tissue. It is used for pipe insulation to ensure the correct temperature of water flowing through. Secondly, it is also a fantastic choice for roofing tissue. It is used to produce bitumen membrane or bitumen shingles – whatever serves the purpose well. Moreover, it is also used as a fiberglass floor tissue that produces PVC floors.  Apart from this, this is also an incredible choice for creating PVC carpets with long-lasting durability.

Coming over to its uses as a surface tissue, this is a go-to choice for many builders. Wondering why? As it is used for the surface treatment of Fiber Reinforced Plastic products. There's more to it – the fiberglass facing tissue can be used for internal wall decoration without worrying about leakage issues. Talking about wallboards and wallpaper choices, this fiberglass wallpaper and fiberglass facing tissue for wallboards are abundantly used to cover wallboard and internal wall decoration. Covering up acoustic boards is an issue in most households as well as buildings. This serves that purpose well too. Go for Fiberglass Acoustic Mat as it can be easily used as a surface layer of the acoustic board. The reason being that it is coated with CaC03 compound through a particular treatment.

Further, over to its battery use, this fiberglass battery separator tissue can be used as a lead-acid battery separator. Also, the commonly available black tissue is an excellent choice for thermal insulation. It can be for different materials; it serves as an insulation tape or insulation board, both. Lastly, fiberglass yellow tissue is also a good choice. It is widely being used as thermal insulation material to cover up the surface of the mineral wool board.

Glass Fiber Mat: Qualities

· Cost-Effective

· Corrosion Resistant

· Excellent Strength

· It comes with an amazing strength to weight ratio

· Has high heat distortion temperature

· The incredible quality of being electrically non – conductive

· Ability to be moulded to precise tolerances

  Glass fiber is an organic substance, which itself is not harmful to the human body. But fine fiberglass dust is breathed into a person's lungs. Because glass cannot be absorbed and decomposed at all, it will form deposits for a long time, which will cause occupational diseases similar to silicosis. Although the damage is not fatal, it will affect people's respiratory function. Contact dermatitis often occurs in glass fiber workers, and a few people Skin sensitization occurs, but the fibers themselves have not been proven to be allergens so far.

If it's just pure skin contact, there are generally no other problems, the main reason is that it irritates the skin to a certain extent.

The opposite of Glass fiber is an inorganic non-metallic material with excellent performance. There are many kinds. The advantages are good insulation, strong heat resistance, good corrosion resistance and high mechanical strength, but the disadvantages are brittleness and poor wear resistance. It is made of glass balls or waste glass through high-temperature melting, wire drawing, winding, weaving and other processes. The glass fiber is often used as reinforcing material of composite material, electrical insulation and heat insulation materials, substrate and other national economy fields.

Our company has been engaged in the glass fiber industry for more than ten years, and has rich experience and high-quality products. Welcome to contact us by fiberglass@njefg.com

China Fiberglass self-adhesive tape catalog of Fiberglass Self-Adhesive Tape for Construction Material, Fiberglass Drywall Joint Tape for Wall Gap Jointed provided by China manufacturer

Get fiberglass mat for wall covering on for use in a wide range of industrial applications. Find the fiberglass mat for wall covering you need for reliable results in construction or production. ... Fiberglass Wall Covering Tissue Mat with crack-resistance.

wholesale terry cloth fabric less more Cloth Teflons Silicone Tape For ACF Cable Bonding is made of heavy PTFE coated fiberglass , single sided or double sided coated with high temperature resistant silicone adhesive (No residual glue).It can resistance 300 degrees.

Made from high density glass wool, Each panel is fully encapsulated with micromesh and edges are resin-hardened to assure safe handling during installation. Primacoustic Acoustic Panels are then covered in a tough yet

5.3 Melt blown. The melt blown process is a nonwoven manufacturing system involving direct conversion of a polymer into continuous filaments, integrated with the conversion of the filaments into a random laid nonwoven fabric. First developments in this field of technology in the industrial area started around 1945.

FRP pultrusion profiles have all kinds of FRP pipe, FRP rectangular pipe, FRP rods, and glass steel beams. The elementary element of the FRP pultrusion profiles for resin and glass fiber (including cloth, carpets, etc) It has good dimensional stability, excellent, corrosion resistance, good surface properties.

white color Spunlace Non woven fabric for wet wipes and tissue,rayon nonwoven.

Duramax PVC Wall Panels is the premier manufacturer of Plastic Panels and Vinyl Wall Paneling. Vinyl panels are a perfect replacement for FRP Wall Panels. pvc panel hot line (323) 471-3360 (7:30 am to 4.30 pm M-F P.T.) Wall