grey fiberglass screen- China Manufacturers Factory Suppliers

    Fiberglass membranes are manufactured from 100% borosilicate glass fibers and include binder-free, chemically inert and binder-containing types. The purpose of adding binder is to enhance the mechanical strength of the glass fiber membrane. It is mainly used to filter coarse particles (such as macromolecular substances, dust). In order to avoid chemical reactions with the filtered substance, glass with inorganic binder is used when filtering organic substances. Fiber membrane, choose glass fiber membrane with organic binder when filtering inorganic substances. This depth filter membrane has the characteristics of fast flow rate, large load capacity and extremely fine retained particles, which can reach the range of submicron particles. The glass fiber membrane can withstand a temperature of 500°C, and can be used for specific gravity analysis and high-temperature gas filtration that require ignition.

    Grade GF/A: For high-efficiency routine filtration, including waste water pollution detection, for filtered water, algae and bacterial culture, food analysis, protein filtration and radioimmunoassay of weak beta emitters, recommended for particulate matter in air pollution monitoring Gravimetry, stack sampling and adsorption, etc.

   Grade GF/B: Used to retain fine particles, fast flow rate. Especially suitable for sample processing with high suspended fine particles in liquid clarification or particle quantification. It can be used for pre-filtration of fine particles before membrane filtration, as a stationary phase in LSC (liquid-solid chromatography), and for protein binding.

    Grade GF/C: Standard filter paper for collecting suspended solids in drinking water, natural water and industrial wastewater. Quickly and efficiently clarifies aqueous solutions containing small to moderately fine particles. Widely used in cell harvesting, liquid scintillation counting and binding assays when higher loads are required.

    Grade GF/D: A common membrane pre-filtration material that can be used with GF/B to provide a very effective graded pre-filtration protection for the membrane.

    Grade GF/F: Commonly used for DNA binding, adsorption and purification, protein binding, and the effect of filtering fine precipitated proteins is obvious. The combination    of GF/F and GF/D can be used as a pre-filter membrane to purify extremely difficult to clarify biochemical solutions, fluids and nucleic acids .

   Grade GF10: Commonly used in roll filter membranes in automatic air filtration devices.

   If you want to know more details, you can contact on fiberglass@njefg.com.

                                         Why is fleece used in fiberglassing.

1. It is a reinforcing material

In the process of GRG production, gypsum slurry and glass fiber are used alternately, layer by layer. The glass fiber helps to strengthen the firmness of the gypsum block and prevent the gypsum from being scattered after solidification.

2. It has high temperature resistance

It has been tested that when the temperature reaches 300°C, it has no effect on the strength of the glass fiber

3. It has high tensile strength

The tensile strength of glass fiber is 6.3~6.9 g/d in standard state and 5.4~5.8 g/d in wet state.

4.It has good electrical insulation

Glass fiber has excellent electrical insulation and is an advanced electrical insulation material. It is also used in heat insulation materials and fire shielding materials.

5. It is not easy to burn

Glass fiber can be melted into glass beads at high temperature, which meets the requirements of fire prevention and control in the construction industry.

6. It has good sound insulation

The combination of glass fiber and gypsum can achieve a good sound insulation effect.

7. It’s cheap

Regardless of the industry, cost control is the most important link, and products with high quality and low price will definitely be favored.

Well, the above are the seven advantages of why glass fiber can be widely used in the construction industry. Glass Fiber is a very good substitute for metal materials.

Glass wool is a plate-shaped product that is processed by centrifuging molten glass into fibers and solidified by adding an environmentally friendly formula binder based on thermosetting resins. The slender glass fiber has a low thermal conductivity and can trap air well, thereby playing the role of thermal insulation, sound absorption and noise reduction, and safety protection. The glass wool board series has the characteristics of tight and firm material, smooth surface and strong pressure resistance, and the appearance is more crisp and beautiful after installation.

Glass wool can be mainly used in: roof insulation, cold insulation, sound-absorbing materials; building insulation, cold insulation; entertainment venues, theaters, TV stations, radio stations, laboratories, sound-absorbing treatment; air-conditioning pipeline freezing and heat insulation of refrigerated warehouses.

It can be processed into glass wool felt according to actual needs, saving space, reducing costs and avoiding unnecessary waste.

The sound absorption characteristics of centrifugal glass wool are not only related to thickness and bulk density, but also related to factors such as cover material and structural structure. In construction applications, it is also necessary to take into account many aspects such as cost, appearance, fire prevention, moisture resistance, dust resistance, and aging resistance.

In large spaces such as gymnasiums and workshops, in order to absorb and reduce noise, sound-absorbing bodies with centrifugal glass wool as the main sound-absorbing material are often used. Sound-absorbing bodies can be made into plates, columns, cones or other special-shaped bodies according to requirements. , The sound-absorbing body is filled with centrifugal glass wool, and the surface is wrapped with a sound-transmitting surface layer. Since the sound-absorbing body has multiple surfaces for sound absorption, the sound absorption efficiency is very high.

In the road noise barrier, in order to prevent noise reflection, it is necessary to take sound absorption measures on the side facing the vehicle, and centrifugal glass wool is often used as the filling material, and the surface layer is a barrier plate made of perforated metal plate. In order to prevent glass wool from absorbing water and getting damp outdoors, it is sometimes wrapped with PVC or plastic film.

Please contact fiberglass@njefg if necessary.fiberglass

Fiberglass insulation is one of the most popular ways to keep your home warm. Since it's inexpensive, easy to find, and very dense, you can't go wrong with padding your walls. However, it's very squishy, so you might be a little confused about how to cut it. This is a very abrasive material that requires a sharp blade and some safety gear such as a dust mask and glasses. However, with some basic techniques, you can cut insulation board safely and efficiently.

1. Measuring insulating materials

   Choose a piece of plywood that is at least as wide as the fiberglass board. Place it on a flat surface so there is enough room to spread out the fiberglass. The plywood doesn't have to be too big, just make sure it fits underneath the part you're cutting. [
   

   Choose a sturdy piece of material, such as a piece of old plywood

   You can put plywood on the floor for protection.

   Avoid cutting bare surfaces such as concrete.

2. Wear cut-resistant gloves and other protective clothing. Fiberglass insulation is skin irritating, wear long pants and a long-sleeved shirt. Then, put on gloves, and some also wear disposable coveralls to prevent the insulation from spreading onto their clothing.

   If part of your skin is exposed, apply some baby powder on it. The powder prevents glass shards in the insulation from sticking to the skin.

3. Wear a dust mask and safety glasses for protection. A regular N95 cloth dust mask will do just fine, if the mask you're using doesn't cover your eyes, buy separate glasses. Wear safety gear whenever cutting insulation.

   The dust released by the insulation is harmful and can aggravate breathing problems such as asthma.

   If you can, work outside so that dust doesn't settle in your home.

4. Unroll the insulating paper face down. Fiberglass insulation is rolled into a roll. Place the roll over the edge of the plywood. Then, push it through the plywood. Spread out just enough to make the cut you want to make.

   Most insulation has a paper backing on one side. It's usually easier to cut the paper last, and the backing keeps the insulation clean when you unroll it.

5. Use a tape measure to determine where you will cut the insulation. Start by measuring where you plan to install the insulation. Plan to cut the insulation 1 inch (2.5 cm) larger than the insulation on all sides. Because fiberglass insulation is flexible, it can be tucked into tight places. The extra length will help it stay in place.

6. Mark the measurements on the insulator with a permanent marker. Use a tape measure to transfer the measurement to the insulator. Measure along both sides of the insulation, making small marks to indicate where you plan to cut.

   If you roughly cut the insulation to approximate size, you don't need to take any additional measurements. If your goal is a precise cut, you can use a piece of sawdust to make a straight cut in most cases.

  Glass fiber is an organic substance, which itself is not harmful to the human body. But fine fiberglass dust is breathed into a person's lungs. Because glass cannot be absorbed and decomposed at all, it will form deposits for a long time, which will cause occupational diseases similar to silicosis. Although the damage is not fatal, it will affect people's respiratory function. Contact dermatitis often occurs in glass fiber workers, and a few people Skin sensitization occurs, but the fibers themselves have not been proven to be allergens so far.

If it's just pure skin contact, there are generally no other problems, the main reason is that it irritates the skin to a certain extent.

The opposite of Glass fiber is an inorganic non-metallic material with excellent performance. There are many kinds. The advantages are good insulation, strong heat resistance, good corrosion resistance and high mechanical strength, but the disadvantages are brittleness and poor wear resistance. It is made of glass balls or waste glass through high-temperature melting, wire drawing, winding, weaving and other processes. The glass fiber is often used as reinforcing material of composite material, electrical insulation and heat insulation materials, substrate and other national economy fields.

Our company has been engaged in the glass fiber industry for more than ten years, and has rich experience and high-quality products. Welcome to contact us by fiberglass@njefg.com

Fiberglass floor paper products are the base material for vinyl floors and decorative wallpapers. The floor and wallpaper made of this product have the characteristics of good stability, smooth appearance, bright color, and convenient laying. It is widely used as decoration materials in public entertainment places such as hospitals, schools, libraries, etc. It can also be used in high-grade floors and walls such as hotels, shopping malls, conference halls, office buildings, and residences.

Here is the content list:

• Features of the fiberglass floor papers we sell
  

• How can we provide you with products?

Features of the fiberglass floor papers we sell

The fiberglass floor paper we sell is evenly dispersed, with a smooth surface, less wool, and easy-to-apply PVC. It is also stiff, resistant to folding, not easily deformed, and has good dimensional stability.

The PVC floor produced with fiberglass floor paper has the characteristics of good stability, smooth appearance, bright color, and convenient installation. PVC floor is a decorative material widely used in hospitals, schools, libraries, airports, and other public places.

How can we provide you with products?

Our products are packaged in standard export packaging for shipping.

1. Roll packing: PE plastic film.

2. Pallet Packing: Pallets should not be stacked in more than 2 layers.

3. The tray is free of fumigation, and a fumigation certificate can be provided.

Our fiberglass floor paper products should be stored in a dry, ventilated, rain-proof place with a temperature of 5°C to 35°C and a humidity of 35% to 65%. It is recommended to keep the intact packaging when not in use to avoid moisture.

If customers need specific unit weight, tensile strength, roll width, and roll length, NANJING EFG can produce according to customer requirements and provide tailor-made services to customers from different countries.

Our fiberglass floor paper products are loaded using standard export loading.

NANJING EFG has delivered materials to US, EU, Middle East, North Africa, South Africa, and Asia customers with guaranteed quality and good feedback. With rich export experience and technical support, NANJING EFG welcomes cooperation with customers from all over the world.

The materials are packed in the factory, then shipped to the seaport, and finally shipped to the customer's port by MSK, MSC, CMA, COSCO, YANGMING, APL, etc.

【Payment method】 LC, T/T, CAD, PAYPAL, WESTERN UNION, ETC.

【After-sale service】

Nanjing EFG CO., LTD tracks the goods of each shipment until the customer uses the material, and is ready to provide any assistance to the customer's needs.

【Technical Support】

If customers encounter any technical problems, Nanjing EFG CO., LTD will provide relevant knowledge to help customers find the best solution, and send technicians to customers' factories for guidance when necessary.

If you are interested in purchasing fiberglass, visit our website: https://www.china-fiberglass.com/to get more professional information about fiberglass. We will welcome you with high-quality products and good service as well as low prices! To provide comprehensive technical support to our customers, we will provide technical and other related information on time upon request.

Drywall Compound weighs up to 35% less than conventional drywall ready-mixed compounds and boasts superior handling and ease of use attributes, allowing you to complete the job at a

Foam glass gravel is a highly stable and versatile product that has been successfully used in construction of buildings and infrastructure projects in Europe for over twenty years. Foam glass gravel has multiple applications: building insulation, green roofs, frost heave insulation, and embankments. Foam glass aggregate retains its structural ...

TaoFibre ceramic fiber paper features light weight, structure uniformity and low thermal conductivity, which serve as a perfect solution for high temperature insulation, chemical corrosion resistance, and thermal shock resistance. TaoFibre ceramic fiber paper can be used in various types of refractory and sealing applications.

Spunbond polyester mat for watrerproofing membrane on sale manufacturers, find details about Spunbond polyester mat for watrerproofing membrane manufacturers, supplier and wholesaler

Fiberglass / Polyester Laid Scrim. Roll Width. Max 3,100mm or cut as customized. Roll Length. Up to 10,000 Meters. Filament yarns. Fiberglass, Polyester filament etc. Pattern construction.

Polyester Nonwoven Manufacturers, Factory, Suppliers From China, Always for the majority of business users and traders to provide best quality products and excellent service. Warmly welcome to join us, let's innovation together, to flying dream.

China Waterproof Polyester Mat wholesale

plywood Fiberglass Board for exterior insulation on sale manufacturers, find details about plywood Fiberglass Board for exterior insulation manufacturers, supplier and wholesaler