woven glass tape- China Suppliers Factory Manufacturers

Fiberglass insulation is one of the most popular ways to keep your home warm. Since it's inexpensive, easy to find, and very dense, you can't go wrong with padding your walls. However, it's very squishy, so you might be a little confused about how to cut it. This is a very abrasive material that requires a sharp blade and some safety gear such as a dust mask and glasses. However, with some basic techniques, you can cut insulation board safely and efficiently.

1. Measuring insulating materials

   Choose a piece of plywood that is at least as wide as the fiberglass board. Place it on a flat surface so there is enough room to spread out the fiberglass. The plywood doesn't have to be too big, just make sure it fits underneath the part you're cutting. [
   

   Choose a sturdy piece of material, such as a piece of old plywood

   You can put plywood on the floor for protection.

   Avoid cutting bare surfaces such as concrete.

2. Wear cut-resistant gloves and other protective clothing. Fiberglass insulation is skin irritating, wear long pants and a long-sleeved shirt. Then, put on gloves, and some also wear disposable coveralls to prevent the insulation from spreading onto their clothing.

   If part of your skin is exposed, apply some baby powder on it. The powder prevents glass shards in the insulation from sticking to the skin.

3. Wear a dust mask and safety glasses for protection. A regular N95 cloth dust mask will do just fine, if the mask you're using doesn't cover your eyes, buy separate glasses. Wear safety gear whenever cutting insulation.

   The dust released by the insulation is harmful and can aggravate breathing problems such as asthma.

   If you can, work outside so that dust doesn't settle in your home.

4. Unroll the insulating paper face down. Fiberglass insulation is rolled into a roll. Place the roll over the edge of the plywood. Then, push it through the plywood. Spread out just enough to make the cut you want to make.

   Most insulation has a paper backing on one side. It's usually easier to cut the paper last, and the backing keeps the insulation clean when you unroll it.

5. Use a tape measure to determine where you will cut the insulation. Start by measuring where you plan to install the insulation. Plan to cut the insulation 1 inch (2.5 cm) larger than the insulation on all sides. Because fiberglass insulation is flexible, it can be tucked into tight places. The extra length will help it stay in place.

6. Mark the measurements on the insulator with a permanent marker. Use a tape measure to transfer the measurement to the insulator. Measure along both sides of the insulation, making small marks to indicate where you plan to cut.

   If you roughly cut the insulation to approximate size, you don't need to take any additional measurements. If your goal is a precise cut, you can use a piece of sawdust to make a straight cut in most cases.

  Glass fiber is an organic substance, which itself is not harmful to the human body. But fine fiberglass dust is breathed into a person's lungs. Because glass cannot be absorbed and decomposed at all, it will form deposits for a long time, which will cause occupational diseases similar to silicosis. Although the damage is not fatal, it will affect people's respiratory function. Contact dermatitis often occurs in glass fiber workers, and a few people Skin sensitization occurs, but the fibers themselves have not been proven to be allergens so far.

If it's just pure skin contact, there are generally no other problems, the main reason is that it irritates the skin to a certain extent.

The opposite of Glass fiber is an inorganic non-metallic material with excellent performance. There are many kinds. The advantages are good insulation, strong heat resistance, good corrosion resistance and high mechanical strength, but the disadvantages are brittleness and poor wear resistance. It is made of glass balls or waste glass through high-temperature melting, wire drawing, winding, weaving and other processes. The glass fiber is often used as reinforcing material of composite material, electrical insulation and heat insulation materials, substrate and other national economy fields.

Our company has been engaged in the glass fiber industry for more than ten years, and has rich experience and high-quality products. Welcome to contact us by fiberglass@njefg.com

The need of every household and a must in every building construction, fiberglass tissue has been the talk of the town for ages. But what does it do? What is it used for? Let us help you put a full stop to your pondering! Fiberglass fleece is a fine matting that is similar to tissue paper. It is produced from glass fiber, be widely used in FRP composite surface applications and ensures smoothness and a clean look of colour to the surface. That isn't it; it also helps thermal resistance and ensures the durability of the product.

Fiberglass: Uses

Having diversified uses, this fiberglass veil acts as an excellent fiberglass pipe wrapping tissue. It is used for pipe insulation to ensure the correct temperature of water flowing through. Secondly, it is also a fantastic choice for roofing tissue. It is used to produce bitumen membrane or bitumen shingles – whatever serves the purpose well. Moreover, it is also used as a fiberglass floor tissue that produces PVC floors.  Apart from this, this is also an incredible choice for creating PVC carpets with long-lasting durability.

Coming over to its uses as a surface tissue, this is a go-to choice for many builders. Wondering why? As it is used for the surface treatment of Fiber Reinforced Plastic products. There's more to it – the fiberglass facing tissue can be used for internal wall decoration without worrying about leakage issues. Talking about wallboards and wallpaper choices, this fiberglass wallpaper and fiberglass facing tissue for wallboards are abundantly used to cover wallboard and internal wall decoration. Covering up acoustic boards is an issue in most households as well as buildings. This serves that purpose well too. Go for Fiberglass Acoustic Mat as it can be easily used as a surface layer of the acoustic board. The reason being that it is coated with CaC03 compound through a particular treatment.

Further, over to its battery use, this fiberglass battery separator tissue can be used as a lead-acid battery separator. Also, the commonly available black tissue is an excellent choice for thermal insulation. It can be for different materials; it serves as an insulation tape or insulation board, both. Lastly, fiberglass yellow tissue is also a good choice. It is widely being used as thermal insulation material to cover up the surface of the mineral wool board.

Glass Fiber Mat: Qualities

· Cost-Effective

· Corrosion Resistant

· Excellent Strength

· It comes with an amazing strength to weight ratio

· Has high heat distortion temperature

· The incredible quality of being electrically non – conductive

· Ability to be moulded to precise tolerances

Fiberglass is an inorganic non-metallic material with excellent performance. It is made of pyrophyllite, quartz sand, limestone, dolomite, boro site, and boro site as raw materials through high-temperature melting, wire drawing, winding, weaving, and other processes. The diameter of the monofilament is several microns to twenty microns, which is equivalent to 1/20-1/5 of a hair, and each bundle of fiber strands is composed of hundreds or even thousands of monofilaments. Fiberglass is usually used as reinforcing materials in composite materials, electrical insulating materials and thermal insulation materials, circuit substrates, and other fields of the national economy.

Here is the content list:

• Material properties

• Main features of glass fiber

Material properties

Melting point: glass is a kind of amorphous, with no fixed melting point, it is generally considered that its softening point is 500~750℃

Boiling point: about 1000 ℃

Density: 2.4~2.76 g/cm3

When fiberglass is used as a reinforcing material for reinforced plastics, the biggest feature is its high tensile strength. The tensile strength is 6.3 to 6.9 g/d in the standard state and 5.4 to 5.8 g/d in the wet state. Good heat resistance, no effect on strength when the temperature reaches 300 ℃. It has excellent electrical insulation, is an advanced electrical insulation material, and is also used for thermal insulation materials and fire shielding materials. Generally only corroded by concentrated alkali, hydrofluoric acid, and concentrated phosphoric acid.

Main features of glass fiber

Compared with organic fibers, fiberglass has higher temperature resistance, non-combustibility, corrosion resistance, good heat insulation, and sound insulation, high tensile strength, and good electrical insulation. These characteristics make the use of glass fiber far more extensive than other types of fibers, and the development speed is also far ahead.

(1) High tensile strength and small elongation.

(2) High elastic coefficient and good rigidity.

(3) The amount of elongation within the elastic limit is large and the tensile strength is high, so the absorption of the impact energy is large.

(4) Fiberglass is an inorganic fiber, which is non-flammable and has good chemical resistance.

(5) Low water absorption.

(6) The dimensional stability and heat resistance are all good.

(7) Good processability, can be made into different forms of products such as strands, bundles, felts, and woven fabrics.

(8) Transparent and permeable to light.

(9) Good adhesion to resin.

(10) The price is cheap.

(11) It is not easy to burn, and can be melted into glass beads at high temperatures.

NANJING EFG, https://www.china-fiberglass.com/, is a dynamic, creative, experienced, and responsible team. Everyone on the team is committed to providing the best products and services to our customers. Our company has developed a wide range of fiberglass which are tested extensively before leaving the factory to ensure quality. As a professional manufacturer, we specialize in manufacturing the highest quality fiberglass. We have conducted a large number of tests before leaving the factory to ensure the quality. You can consider using our cost-effective products. Thank you for your time!

Glass wool is a plate-shaped product that is processed by centrifuging molten glass into fibers and solidified by adding an environmentally friendly formula binder based on thermosetting resins. The slender glass fiber has a low thermal conductivity and can trap air well, thereby playing the role of thermal insulation, sound absorption and noise reduction, and safety protection. The glass wool board series has the characteristics of tight and firm material, smooth surface and strong pressure resistance, and the appearance is more crisp and beautiful after installation.

Glass wool can be mainly used in: roof insulation, cold insulation, sound-absorbing materials; building insulation, cold insulation; entertainment venues, theaters, TV stations, radio stations, laboratories, sound-absorbing treatment; air-conditioning pipeline freezing and heat insulation of refrigerated warehouses.

It can be processed into glass wool felt according to actual needs, saving space, reducing costs and avoiding unnecessary waste.

The sound absorption characteristics of centrifugal glass wool are not only related to thickness and bulk density, but also related to factors such as cover material and structural structure. In construction applications, it is also necessary to take into account many aspects such as cost, appearance, fire prevention, moisture resistance, dust resistance, and aging resistance.

In large spaces such as gymnasiums and workshops, in order to absorb and reduce noise, sound-absorbing bodies with centrifugal glass wool as the main sound-absorbing material are often used. Sound-absorbing bodies can be made into plates, columns, cones or other special-shaped bodies according to requirements. , The sound-absorbing body is filled with centrifugal glass wool, and the surface is wrapped with a sound-transmitting surface layer. Since the sound-absorbing body has multiple surfaces for sound absorption, the sound absorption efficiency is very high.

In the road noise barrier, in order to prevent noise reflection, it is necessary to take sound absorption measures on the side facing the vehicle, and centrifugal glass wool is often used as the filling material, and the surface layer is a barrier plate made of perforated metal plate. In order to prevent glass wool from absorbing water and getting damp outdoors, it is sometimes wrapped with PVC or plastic film.

Please contact fiberglass@njefg if necessary.fiberglass

Get waterproofing fiberglass tissue on for use in a wide range of industrial applications. Find the waterproofing fiberglass tissue you need for reliable results in

Since 1965, Georgia-Pacific Gypsum has been committed to developing the highest quality gypsum building products in the industry. Our versatile ToughRock gypsum boards are ideal for a wide range of commercial and residential interior applications, and our Dens family of high-performance fiberglass mat-faced gypsum products offer exceptional strength and superior

Product Category. The Acoustic Ceiling is decorative anti-noise and could effectively absorb the noise from the top. Modular Felt acoustic panel Ceiling System. Add to Basket. Acoustic

Wall Panel Systems. Its a difficult balancing act to design beautiful interiors that can also stand the test of time in harsh environments. That led us to create Palladium Wall Panels

Fiberglass carpet tissue is made by advanced wet-formed technology, the main material is E-glass chopped strand and environmentally friendly binder, it is mainly used as substrate for the carpet tile. The carpet tile made of this substrate is an ideal decorative material for flooring decoration in domestic residences on account of their ...

To improve thermal performance of exterior and interior walls and floor/ceiling assemblies. Kraft: non-exposed steel stud construction. Foil: non-exposed wood and steel stud construction. FSK-25: where a Fire Hazard Classification of

Surface tissue used to get a high-quality smooth surface finish on GRP roofing. Surface tissue is a very fine fibreglass mat that is used to achieve a smooth surface and better overall finish on a GRP fibreglass roof. The matting acts as

Find Fiberglass Products Suppliers. Get latest factory price for Fiberglass Products. ... Fibre Reinforced Plastic Bollard extends its applications beyond just protecting various assets from